Philips 50PF9731D/37 relays clicks

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • hijodalgo
    Member
    • Jan 2011
    • 35
    #1

    Philips 50PF9731D/37 relays clicks

    I have this Phlips 50PF9731D/37 the relay,(both of them)clicks and clicks without stopping,and the 5 volts is moving from zero to 5.3 volts.Found two 3300 microfarad caps bulged in the power board,havent changed yet because i just ordered,but i used a general purpose one to make a fast test,and the same symptom is on,,relays never stop clicking..all voltages are moving,,discconet the y sus,same,,any help please..
    Attached Files
    Tags: None
    • 1beertap
      Badcaps Veteran
      • Mar 2009
      • 219
      • USA
      #2
      Re: Philips 50PF9731D/37 relays clicks

      I would suggest replacing all of the caps on power supply board.

        Comment

        • rmoody
          Learning Member
          • Jul 2011
          • 262
          #3
          Re: Philips 50PF9731D/37 relays clicks

          Originally posted by 1beertap
          i would suggest replacing all of the caps on power supply board.
          ditto

            Comment

            Previous template Next

            Related Topics

            Collapse
            • alro7779
              Philips 32PFL4901/F8 BA4GF0F0102 2 Not getting standby led
              by alro7779
              Hello, guys!

              The same 32" Philips TV I was having video issues, but now I don't have standby led at all. Someone here shared with me the schematic of the power supply, and checking the voltages, I see right after the resistor R604 I'm getting 1.6 v which is too low for enabling the Gate of the Q601 mosfet (the diagram says 4.2). On the R614 resistor I'm getting 181 V in and 117 V out, then through R603 I'm getting the same 117 V in and 59.9 V out, finally getting the latter voltage in the R604 BUT getting just 1.6 V out, which is the voltage that goes on to the Gate of the Q601...
              09-14-2025, 12:25 AM
            • G33RT
              Philips 8200 series 65PUS8204/12 stuck at Philips Logo
              by G33RT
              Philips 8200 series 65PUS8204/12 stuck at Philips Logo, it does not reboot it just stays on the logo.

              It does power up when pressing the power button.

              I already try the power button while plugin the plug with no result.
              Also put the latest firmware autorun-TPM191E_R.001.004.100.000.upg on a MBR/FAT32 USB stick at USB port2 with no result either.

              Could this be an PSU or eMMC issue ?
              07-19-2025, 03:43 AM
            • jason123
              Philips 42" TV 42PFL3603D/F7 clicks but No LCD Backlight
              by jason123
              Hi folks,
              I'm suspecting the actual CCFL or EFL being bad, just not sure how to test, but would like to confirm.

              TV clicks upon plugging in AC. When I press the PWR ON button, clicks again.
              LED on the Main board comes on green (Assuming some diagnostics), Blue LED on the TCON comes on also when I turn the TV on, but turns off about 30 seconds later.

              3V3 ST is on (3.26 V)
              Standy 3.3 V (off) when I press power button goes to 0.16 V
              12Vssb is 11.75 V (on), 0.18 V (0ff)
              +12Voud is 13.8V (on) ~ 0V off
              -12Voud is -12.4 V (On) ~0V...
              02-20-2021, 08:04 AM
            • double_DD
              Philips curling iron - is this a common AC cable?
              by double_DD
              Hi all,

              Wife has 2 Philips hair curling irons half defective - after learning how they're supposed to work and testing them, it turned out that both have defective power cables, and both on the same place; broken wires due to wire bending.
              As they were both relatively easy to disassemble, and cables are plugged not soldered (as they can rotate in the handle), I was sure it would be easy to find replacements. But - NO! I'm unable to find anything similar on ebay or Aliexpress.

              Not sure if this is something Philips proprietary, or a standard, but the cable plug...
              08-18-2025, 10:04 AM
            • janos6662000
              Philips 47PFS7509/12 LCD TV problem
              by janos6662000
              Hi

              I have here a Philips 47PFS7509/12 LCD TV which came to me with a weird problem : without signal i could access menu, make a factory reset, access menus, etc.
              When i applied cable signal to check image, i had normal picture, but TV was restarting.
              I downloaded original firmware and applied the update, but the problem remained.
              From a colleague i received a "factory package software" which is a lot bigger.
              I made another firmware update, but still did not solve the problem.
              Somewhere on the way the error got worse, because at the moment the...
              08-12-2025, 12:54 PM
            • Loading...
            • No more items.
            Working...