Vizzion LE40E10 40" - Only Standby Light

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • TVAddict
    Senior Member
    • Jan 2022
    • 69
    • Caribbean

    #1

    Vizzion LE40E10 40" - Only Standby Light

    Hi, as the title says, all i have is the red standby light, tv does not respond when pressing the power button, the red light does not flash/blink.

    It's one of those AIO boards, if anyone can provide any assistance, it would be greatly appreciated.
    Attached Files
    Last edited by SMDFlea; 05-28-2023, 03:49 PM. Reason: Added "LE40E10" to thread title
  • TVAddict
    Senior Member
    • Jan 2022
    • 69
    • Caribbean

    #2
    Re: Vizzion 40" - Only Standby Light

    I've disconnected both the backlight connector and the LVDS ribbon cable, same problem, no response.

    I have a steady 165v across the main caps (68uf 450v)
    Attached Files

    Comment

    • TVAddict
      Senior Member
      • Jan 2022
      • 69
      • Caribbean

      #3
      Re: Vizzion 40" - Only Standby Light

      Not sure as to how to correctly check voltages at this side of the yellow transformer where it says 310v, vcc and gnd
      Attached Files

      Comment

      Related Topics

      Collapse

      • ChristianBr01
        LED TV Samsung The Frame 55 inch QE55LS03RAU Standby Light only
        by ChristianBr01
        Hello everyone,
        I got a Samsung The Frame 55 inch TV for free from uncle cause it is not turning on anymore. I am in the second year of training as an electrician so I have knowledge already but I am far away from to be a pro.
        The TV has Standby but ist not turning on. A Friend of mine owns a 50 inch Frame TV so I checked the One Connect Box and the One Connect Cable there. Both are good and working normally. I have opened the TV case and measured some voltages on the Board.
        What I already found is that the 12.8V are not an the connector to the main board connector to the power...
        04-23-2025, 01:48 AM
      • AleMonti
        LG 55EG910V - no power and no standby light
        by AleMonti
        Hi everyone,
        I'm trying to troubleshoot and repair this old LG OLED curved TV, model 55EG910V.
        I did some basic troubleshooting and reviewed most related posts here, but I wasn't able to isolate the issue.

        The TV shut itself off during playback and never came back to life - the standby light remains off. My dad claims that it has happened a few times in the past but the issue resolved itself after some time. Not this one.

        After checking the basics I did the following:
        • I measured all voltages and as expected the only active supply is the 3.5V standby. It
        ...
        11-04-2024, 05:02 PM
      • Kaar3l
        Samsung QLED QE65Q7FNAT only standby light
        by Kaar3l
        TV: Samsung QLED QE65Q7FNAT
        PSU: BN4400940A
        MB: BN94-12832K

        I got the tv in spring 2024. At that time it started, then ran 60 sec and poweroff. Seemed like reboot issue. I didn't have time and room to check it in summer so I plugged it in and now the standby light is on. I press button on remote, standby light goes off and tries to start?. No picture or backlight on LCD. I thought about removing diodes like in this thread: https://www.badcaps.net/forum/troubl...sung-qled-q60r...
        09-24-2024, 01:35 PM
      • jasonbay13
        Philips 37HFL5682L/F7 no standby light, incomplete service manual?
        by jasonbay13
        picked up a tv and when the power is plugged, the standby light flashes real quick then goes off. of 3.3, 12, 24v is all there but i couldnt find any 5v on the back-end board. ON/OFF is low, which it seems is what turns on the backlight so i removed the wire at the back-end board and put a 10k resistor to the 3.3v, which when plugged in brings on the backlight for a split second and also a blue light "LED1" on the inverter board, which goes off after a short time.
        am i missing something to bring on the backlight or is the inverter/ccfl gone bad? would that cause the inverter board...
        12-01-2023, 09:55 PM
      • Nicktronic
        Samsung UN70NU6070F Standby Light flashes twice
        by Nicktronic
        Hey Everyone,

        So I've got this Samsung and the reported issue is that when powered on the backlight comes on, but no picture, no sound, it will flicker, the standby light will flash red twice and repeat the whole process...each loop lasts about 15 seconds.

        I've googled the issue and understand it is likely a panel/driver board issue, but was hoping the "tape method" could be successful. Before I did that though, I disconnected the left LVDS cable and powered the TV on. This time I got sound, no picture and the two blink standby light stopped. Did the same...
        03-27-2023, 07:01 PM
      • Loading...
      • No more items.
      Working...