HI please i need data scheet or Pin out super I/O KB9022Q D (ENE)
-
-
Re: Need data scheet I/O KB9022Q D (ENE)
Datasheet not available. Pinout should be same as 9012 though i'm not 100% sure. Anyway having difficulties in read/write kb9022 with RT809F as well as svod. -
Re: Need data scheet I/O KB9022Q D (ENE)
Yes I tried same as kb9012 but can't read and write successfullyComment
-
Re: Need data scheet I/O KB9022Q D (ENE)
đâyComment
-
Re: Need data scheet I/O KB9022Q D (ENE)
Would anyone have a register description for the EC in I/O KB9022Q D? Or have any info about which registers are involved in controlling the fan speed? I'm trying to make a configuration file for notebook fan control...Comment
-
Re: Need data scheet I/O KB9022Q D (ENE)
thank you for kb9022q datasheet.Comment
-
Re: Need data scheet I/O KB9022Q D (ENE)
thanksyou very much .Comment
-
Re: Need data scheet I/O KB9022Q D (ENE)
Thanks a lot! ��Comment
-
Re: Need data scheet I/O KB9022Q D (ENE)
hi anybody know which is the compatible IO suitable with kb9022?Comment
-
Re: Need data scheet I/O KB9022Q D (ENE)
Thanks bro.
Comment
-
Re: Need data scheet I/O KB9022Q D (ENE)
that is not datasheetComment
-
Re: Need data scheet I/O KB9022Q D (ENE)
thank youComment
-
-
Re: Need data scheet I/O KB9022Q D (ENE)
Thanks bro.Comment
-
Re: Need data scheet I/O KB9022Q D (ENE)
I have an Acer a515 51g model laptop. It uses the same motherboard. If anyone can manage to make a fan control file, can they send me the config file?Comment
-
Re: Need data scheet I/O KB9022Q D (ENE)
Kb9022Q D error at Blank check with SVOD anybody has done it yet ?
Blank Check FalseComment
-
Problem
This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached.... -
Hello, A customer told us that there is a data recovery company that can by pass IMac pro 2020 with t2 chipset GPU to get their data back, I am wondering if that is possible. GPU is shorted and Imac wont boot at all. I informed customers that data are almost impossible to be retrived, and they are upset and think we are BS them. Of course being up in Canada, people like to believe that usa will have a better solution for it, a US data recovery company they searched on google told customer that they could get the data back without needing worry about T2 chip or Imac not working all that, I do not... -
Hello,
Here I have the mentioned tablet with motherboard s6000-mb-h401. The tablet won't turn on, no display, charging normally. I manage to connect to UART port and got this output when I try to start it:
...Code:[PWRAP] pwrap_init_preloader [PWRAP] pwrap_init [PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=0 rdata=5AA5 [PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=1 rdata=5AA5 [PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=2 rdata=5AA5 [PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=3 rdata=5AA5 [PMIC_WRAP]wrap_init pass,the return
-
Hi, I'm an elevator technician. The attached oscilloscope display picture is from a digital elevator hall arrival lantern data signal. We have been having problems with “ghost signals” causing intermittent hall arrival lanterns to illuminate randomly when the elevator is not actually due to arrive at the floor.
The tech support of the hall arrival board manufacturer (CE Electronics) is blaming the elevator controller manufacturer (MCE), and the tech support of the elevator controller blames the hall arrival board manufacturer.
The boards are powered by a ground referenced... -
Patient is a Maytag/Whirlpool/Kenmore clothes dryer. Not sure of exact model, doesn't matter. All boards are out of production.
Specific problem is a Maytag 8544799 / WP8544799 motor-control board, aka Diehl Controls 708879-05. Customer states the board "doesn't work, motor doesn't run". Not sure how the repairman made that assessment, or if it's even accurate. He can't get replacement boards, and the owner decided to buy a new dryer, so whether this board is the problem is speculation on his part. Again, doesn't matter.
I've been over the board looking for...
Comment