Hp 650 g4 DMI error

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • laptopcenter
    Senior Member
    • Mar 2019
    • 90
    • haifa

    #1

    Hp 650 g4 DMI error

    Hello
    I have problem when I flash bios it gave me this error please help
    Attached Files
  • SMDFlea
    Super Moderator
    • Jan 2018
    • 20705
    • UK

    #2
    Re: Hp 650 g4 DMI error

    Originally posted by laptopcenter
    Hello
    I have problem when I flash bios it gave me this error please help
    Fix not fully configured message https://www.badcaps.net/forum/showth...light=sssm.bat
    All donations to badcaps are welcome, click on this link to donate. Thanks to all supporters

    Comment

    Related Topics

    Collapse

    • Superbee_dad
      Sharp 80” long short flash backlight error - Help
      by Superbee_dad
      Hello Sharp TV experts
      Our Sharp LC-80LE642U displays one short one long flash error code which is a backlight error. I went into service mode and there were 8 lamp error counts recorded. I reset the count to 0 and did a reset. The last monitor error cause was 16 B00014639:12. 16 is the code for backlight error. I tried to power the tv up but went back into error mode.

      > I checked voltages on the power supply board and they all check out .. including 3.28 volts at the error pin.
      > There is power to the cpu and T-CONN and no faults found there. The cpu has a flashing...
      01-24-2025, 11:51 PM
    • KevinWysocki
      Aya A39FHD3901/2 - Vestel 17MB82 mainboard - LED blinking
      by KevinWysocki
      Hi there,

      My mother in law gave me an Aya TV, to take a look if I could do something to repair it.

      At startup, LED constantly blinks and no image is shown (even if I light the screen, broken backlight is not the problem), also +12V power rail is fine.

      After some research, it seems that NOR flash often fails on this mainboard, I have found the procedure to force flash upgrading with a USB key connected to mainboard USB port, pressing "OK" button on the remote and plugging the TV power cord.

      Flash upgrade didn't seem to work,...
      08-20-2023, 09:45 AM
    • Sus256
      HISENSE 65E7KQ PRO - no boot
      by Sus256
      Hi all!

      HISENSE 65E7KQ PRO
      RSAG7.820.13512 - chassis
      MT9618BAATAB - cpu
      RSAG7.820.12059 - power
      HD650Y3U77 - panel
      KLM8G1GETF - emmc

      The TV does not turn on, the standby indicator is on. All voltages are present.
      Emms is dead. Not readable, not detected.
      Replaced emmc.
      But with another dump there is no launch

      Terminal log

      UART
      <
      AC_ON
      RPMB key is not yet programmed

      HASH1_VERSION=0x00000000 64bit
      E-B
      FDE enabled
      layout pattern onebin by SAR7,0...
      06-01-2025, 02:11 AM
    • kyrios
      Flash LG PK5 DEMO - CH431A ERROR - verification error on address 00000000
      by kyrios
      Hello!

      I apoligize for my English. I need some help.

      I have an LG PK5 in demo version and trying to repair it, I found the original firmware in this forum to flash speaker to the original version.
      Without having any idea about these things, I give thanks this forum and other tutorials, I bought a CH431A programmer and I have tried to do all the steps but after reading the new firmware, in the "verification" step I get this error: verification error on address 00000000
      Could someone help me to solve it, please?

      Thank you so much
      11-30-2023, 01:06 PM
    • ekozeko333
      [Help] Lenovo Yoga Slim 7-14ARE05 (DA0LS3MBAF0) – 25Q80DVN1G Flash Is All FF, USB-C PD Stuck at 5V
      by ekozeko333
      Hi all,
      I’m trying to recover a Lenovo Yoga Slim 7-14ARE05 with board DA0LS3MBAF0 Rev:F. I’ve run into an unusual issue where USB-C PD is stuck at 4.7–5V and the system won’t boot (keyboard lights flash briefly, then nothing).
      🔥 The Problem Started After Suspected ESD/PD Fault
      I experienced a power issue or ESD event through a USB-C charger
      After that, the NX20P5090 power switch was visibly burned and was replaced
      Now the PD controller always negotiates 5V @ 2A, even with known-good chargers
      🧠 What I’ve Done So Far
      Flashed...
      06-21-2025, 02:48 AM
    • Loading...
    • No more items.
    Working...