Re: HELP!!! need working EC rom for t480s on mec1663
i tried another RT809F, but an error is the same ((
HELP!!! need working EC rom for t480s on mec1663
Collapse
X
-
-
Re: HELP!!! need working EC rom for t480s on mec1663
This is my dump after i flash the BIN from first post.Attached FilesLeave a comment:
-
Re: HELP!!! need working EC rom for t480s on mec1663
Yes, i did this, but there is the sam error. before i just put resistor on r544 placeLeave a comment:
-
-
Re: HELP!!! need working EC rom for t480s on mec1663
i think yes, but not sure. Can you help me with it?Leave a comment:
-
Re: HELP!!! need working EC rom for t480s on mec1663
When i flash it i`m getting an error : Chip verification error, start position: 0x3FC00.
Programmer is RT809H.
There is a full log:
016: MEC Chip ID: 0x200024B1
017: Start erasing chip, please be patient......
018: Auto blank checking...
019: Blank check successful,Elapsed time:4.939 seconds.
020: Erase successful,Elapsed time:5.58 seconds.
021: >------------------------------------OK---------------------------------------<
022: C:\USERS\USER\DOWNLOADS\T480S_EC_N22HT37W\T480S_EC_N22HT37W.BIN
023: File has been loaded, checksum: 16bits_0x48BF ,32bits_0x020948BF :
024: MEC Chip ID: 0x200024B1
025: Start writing chip......
026: Auto erasing...
027: Erase successful,Elapsed time:0.616 seconds.
028: Start writing...
029: Elapsed time: 17.86 seconds,average speed of 14679 bytes/sec.
030: >------------------------------------OK---------------------------------------<
031: MEC Chip ID: 0x200024B1
032: Start verifying chip......
033: Chip verification error, start position: 0x3FC00.
Chip is recognized normally. Maybe i`m doing something wrong?Leave a comment:
-
Re: HELP!!! need working EC rom for t480s on mec1663
When i flash it i`m getting an error : Chip verification error, start position: 0x3FC00.
Programmer is RT809H.
There is a full log:
016: MEC Chip ID: 0x200024B1
017: Start erasing chip, please be patient......
018: Auto blank checking...
019: Blank check successful,Elapsed time:4.939 seconds.
020: Erase successful,Elapsed time:5.58 seconds.
021: >------------------------------------OK---------------------------------------<
022: C:\USERS\USER\DOWNLOADS\T480S_EC_N22HT37W\T480S_EC_N22HT37W.BIN
023: File has been loaded, checksum: 16bits_0x48BF ,32bits_0x020948BF :
024: MEC Chip ID: 0x200024B1
025: Start writing chip......
026: Auto erasing...
027: Erase successful,Elapsed time:0.616 seconds.
028: Start writing...
029: Elapsed time: 17.86 seconds,average speed of 14679 bytes/sec.
030: >------------------------------------OK---------------------------------------<
031: MEC Chip ID: 0x200024B1
032: Start verifying chip......
033: Chip verification error, start position: 0x3FC00.
Chip is recognized normally. Maybe i`m doing something wrong?Last edited by akhtian; 10-23-2022, 10:01 AM.Leave a comment:
-
Re: HELP!!! need working EC rom for t480s on mec1663
Latest EC update N22HT37W 1.22 attachedAttached FilesLeave a comment:
-
HELP!!! need working EC rom for t480s on mec1663
HELP!!! need working EC rom for t480s on mec1663Tags: None
Related Topics
Collapse
-
by SMDFleaCommon SPI bios chip programming Questions and Answers
----------------------------------------------------------
Q: I have a bios request,i can`t post my backup as i can`t read from the chip.
A: If you can`t read from it how do you expect to write to it ?.
Q: Why is my bios chip unreadable ?.
A: The programmer is faulty or has a worn or broken zif socket.
The USB cable is frayed,connector pins worn or some other physical damage.
Not enough amperage or voltage to power the programmer properly.
Bad...-
Channel: BIOS Requests ONLY!
09-02-2021, 04:40 PM -
-
by SparklingxHi,
So i've bough a ch341 programmer, and the chip was CH341B . the test clamp was not working( when connecting bios using test clamp, ch341 device was disconnecting) I tried soldering the bios on the provided board, soldering the bios I could read the chip but could not write or erase. ASprogrammer , neo, ch341a programmer... all programmer software was hanging and device was disconnecting after few second of erase/write operating.
So then I have soldered a capacitor(whatever I had..[10v ~470uf ] ) from VCC to GND on my provided pcb where you solder the bios
now all... -
Long story short:
- dad converted Asus Chromebox CN62 into Windows compatible, with mrchromebox BIOS, years and years ago
- gave the computer to his son a couple years later
- son now decided to revert it to Chrome OS, to sell it as original (re-writing BIOS with the backup one created by his dad)
- too lazy to remove the board from the case, thought a voltage regulator was the BIOS chip (you know... it has 8 legs)
(seems like the story was not that short)
He used alligator clips to read the chip. No luck reading it. Removed chip and placed on a SOC-8... -
by TroystainHello, anyone here have updated ezp2023+ chip database in .dat file format.
I need to add w25q256jveq chip but I do not know what data should I type.
I'm using the ezp chip dabase editor posted from here https://www.badcaps.net/forum/troubl...ro-programmers
The currenty unit model that I am trying to detect is HP elitebook 640 g9 which is currently locked on admin bios....11-25-2024, 12:53 AM -
by AndreasbestHello.
Received a T480s with broken main Type C, i replaced it but it's not working (replaced it 3 times just to make sure everything is soldered correctly).
Thunderbolt charging works and laptop power up fine.
I need help to repair JUSBC port please.
Thank you!
Schematics: https://www.badcaps.net/forum/troubl...b471#post7297010-21-2024, 12:05 PM - Loading...
- No more items.
Leave a comment: