Re: HP 840 G7 password
Hello there, can someone please remove password?
16 & 32mb dump in attachment.
Thanks.
Hello there, can someone please remove password?
16 & 32mb dump in attachment.
Thanks.
-
-
Re: HP 840 G7 password
Thanks, password is gone
but im getting "Endpoint Security Controller" message at startup.
is there a fix?
ThanksComment
-
Re: HP 840 G7 password
Thanks, did the flash but issue is still thereLast edited by SMDFlea; 09-22-2023, 08:17 AM.Comment
-
Last edited by SMDFlea; 09-22-2023, 08:17 AM.If you have found our forum useful please consider supporting us. Subscribe for a small monthly fee and receive extra benefits including our bios, boardview & schematic archive.
Subscribe to support us. It only takes 1 minute:
https://www.badcaps.net/settings/subscriptionsComment
-
Re: HP 840 G7 password
Thanks! this one worked.
it now shows "System is now booting into manufacturing program mode ... : 31" at the HP logo on the top left every start.
but thats neglible, it works.Comment
-
Re: HP 840 G7 password
Hello.
I tried to remove the BIOS password on an HP 840 G7 and I got this error "Endpoint Security Controller"
The password is still there.
Can you please help?Comment
-
Comment
-
Re: HP 840 G7 password
5cg0393pwcComment
-
If you have found our forum useful please consider supporting us. Subscribe for a small monthly fee and receive extra benefits including our bios, boardview & schematic archive.
Subscribe to support us. It only takes 1 minute:
https://www.badcaps.net/settings/subscriptionsComment
-
Re: HP 840 G7 password
This thread is for the 840 G7 ,do not reply to off-topic posts pleaseOriginally posted by hoaca388
Comment
-
If you have found our forum useful please consider supporting us. Subscribe for a small monthly fee and receive extra benefits including our bios, boardview & schematic archive.
Subscribe to support us. It only takes 1 minute:
https://www.badcaps.net/settings/subscriptionsComment
-
Re: HP 840 G7 absolute lock
Hello
Can someone help me whit this
I need to disable absolute in dump
hp 840 g7
sn:5CG05220LV
I post
25Q80
25Q128
25Q256
Thanks in advance
regards chrisComment
-
If you have found our forum useful please consider supporting us. Subscribe for a small monthly fee and receive extra benefits including our bios, boardview & schematic archive.
Subscribe to support us. It only takes 1 minute:
https://www.badcaps.net/settings/subscriptionsComment
-
Re: HP 840 G7 password
hello hoaca388
Thanks for the support
it works but can you clear the me for me.
Best regards chrisComment
-
If you have found our forum useful please consider supporting us. Subscribe for a small monthly fee and receive extra benefits including our bios, boardview & schematic archive.
Subscribe to support us. It only takes 1 minute:
https://www.badcaps.net/settings/subscriptionsComment
-
Hello, I have an old Dell G3 3579 (ST: 2WQ7LP2-8FC8) with a newer 8FC8 BIOS password. I have successfully attached to the flash chip (W25Q128JVSQ) on the motherboard with a CH341A programmer and made several modifications using Intel FIT (e.g., allow software SPI write) without bricking. I was also able to boot to a modified GRUB shell where I attempted to edit many BIOS security related options like BIOS Guard/Lock, Flash Signature Override, ME FW Image Re-Flash, etc.
Unfortunately, some of these modifications like to Intel BIOS Guard failed because it is fused into the PCH. Also,... -
x1403za r2.1 bios uefi password any one clear my bin file
serial NBN0CV10581747C
board id X1403ZA MAIN BOARD R2.1
bin file
https://drive.google.com/file/d/1jBD...ew?usp=sharing -
Dear Badcaps,
Is there any available method to perform a bios password unlock on an ThinkPad L14 Gen 4?
CPU is Ryzen 3 PRO 7330U.
What about though Lenovo? It has the best support plan. They asked for the receipt, however it was sold though a reseller.
As a sidenote I was always able to unlock any dell laptop with the master code by simply asking dell and providing a reseller/refurbisher receipt.
Thank you very much! -
Hi everyone
I noticed on the Xgpro software the BIOS backup files have extra bytes at the end when reading some chips, this is because the Xgpro software also reads the OTP region of those flash chips, and by default will append that region to the saved file
Programmer models: XGecu TL866II Plus / T48 / T56 / T76
Example: GD25LQ128D (1.8V), IC size is listed as 0x1000000 Bytes (16777216 bytes) + 0xC00 bytes, those extra 0xC00 bytes will be appended to the end of the saved file by default, resulting in a file size of 16780288 bytes
There's also an extra OTP Secu.R... -
Hello everyone, I come here to tell you my problem regarding the power-on password. It is not a bios reset demand, and i can't have any access to windows. This is the bios and power-on password that is blocking all other things.
My Omen 15-dh0052nf purchased second-hand was configured with the bios password upon purchase (very simple password :P ).
Having decided to sell it in order to get something more powerful, I reset all BIOS settings and set a blank administrator password. But the power-on password cannot be changed to a blank one so I let the actual password set....
Comment