Re: ME Firmware Cleaning Guide
how about Gen10? gen 11?
how about Gen10? gen 11?
-
-
Comment
-
Re: ME Firmware Cleaning Guide
some one can share solution clear ME 14.0.xx 15.0.xx for gen 10, gen 11?Comment
-
Re: ME Firmware Cleaning Guide
See this channel , hepful informations
https://www.youtube.com/watch?v=x_PjZyJ_BSQ&t=98sComment
-
Re: ME Firmware Cleaning Guide
i Have a problem when i extract the file the me region is 4.78mb but the cleaned me is 7.0mb
so what is the problemComment
-
Re: HP 840 G1 is not in committed state
@SMDFlea i want to know something.How i replace in Me Region MFS/FTPR/NFTP area.
According to this video.He doing auto how i can manually.
link video
Time 01:12:40 MFS CHUNK DATA CLEAN
https://www.youtube.com/watch?v=j2K5PHqZunkAttached Filesif you find these attachements useful please consider making a small donation to the site
Comment
-
-
Re: HP 840 G1 is not in committed state
You can check with MEAnalyzer how the partitions are laid out and the start and end addresses and size using the -dfpt switch .You can use a hex editor and UEFITool (newer version) to see the partitions use the extract as-is if you want to copy any part from one ME region to edit into another. You can even edit the PCHC,PMC partitionsAttached Filesif you find these attachements useful please consider making a small donation to the site
Last edited by SMDFlea; 07-25-2021, 04:42 AM.Comment
-
-
Comment
-
Comment
-
Re: ME Firmware Cleaning Guide
please i need flash image tool V 12.0.32.1421Attached Filesif you find these attachements useful please consider making a small donation to the site
Comment
-
-
-
Re: ME Firmware Cleaning Guide
i do it with version 12 but the hdd becomes not detectable in setupComment
-
Comment
-
Re: ME Firmware Cleaning Guide
i do clean me region to the bios and i flash pc but hdd becomes not detect in setup and when i flash with the old bios the hdd is detected
the new bios cleared is in the pictureAttached Filesif you find these attachements useful please consider making a small donation to the site
Comment
-
-
Re: ME Firmware Cleaning Guide
Maybe you did something wrong. Post your original bios backup in a new thread,not in this thread please - https://www.badcaps.net/forum/forumdisplay.php?f=40Comment
-
Re: ME Firmware Cleaning Guide
need Intel CSME firmware repository pack for 11.8.83.3874Comment
-
Comment
-
Re: ME Firmware Cleaning Guide
Thank you for sharing this article. Thank you, my friendComment
-
If you have to clean the ME firmware on **some microsoft surface models the touchscreen can stop working.
** Some models do not need this fix.
*You should install the latest updates from microsoft,including the driver packs before assuming there is a hardware problem.* - See Post #2
EDIT: If nothing else works try this fix - https://www.badcaps.net/forum/showpo...8&postcount=40
Always check a working dump from the same model using FIT.If the working dump default setting for "Integrated Sensor Hub Supported" is set to "NO"... -
i know a tool https://github.com/MuertoGB/MacEfiToolkit is capable of SN change and Clean ME but not updating EFI Version of the BIN file. is there a guide or a BIOS structure to update the firmware??...03-06-2024, 01:34 AM -
Hi,
I have an Anker SoundCore 2 (A3105) that I saved from the trash (well, I guess there's a reason why it was supposed to go into the trash...). The problem is that it always turns off after a few seconds (sometimes it stays on a bit longer, between 30 and 60 seconds, but it still turns off). The power light turns on and the bluetooth light starts blinking, but both abruptly turn off again. The "turn off sound" is still played after the lights turn off. Sometimes, it also loops the on-off cycle several times without me pressing any buttons. If I connect an AUX cable, music...08-11-2025, 02:14 PM -
Hello to everyone ,
This is my first post here, and i would like to share with you a small story in case you can help me.
Docker Type-C Gen 2 - Model 40AS. Was given to me by a friend for free ,but with the problem that you cannot use the video output ports.
All ports work , USB , Ethernet, Type C ... but HDMI + Display Port don't work
I searched on reddit and google for problem similar to that, and a LOT of people had fixed this problem by updating the firmware. So i tried , i searched and found 1.1.13 utility and 1.1.20 utility that can help... -
Hi guys.
I've got a Ubiquiti US-8-150W POE switch which has issues with updating the firmware.
Turned out to be a bad EEPROM chip. It would read the firmware and work as normal, but failed to write new firmware to it.
So I took off the chip and read on EEPROM and saved it. Wrote to old chip and failed to write
Got New chip and writes good.
THE PROBLEM...
It fails to fully load the firmware, POE lights fail to work during g firmware test during load. I'm suspecting bad EEPROM Read.
Does anyone have a Good Firmware I can have?...
Comment