HP DMI Tool NBDmiFit

[delos23]

Re: HP DMI Tool NBDmiFit

Hello, So I'm currently working on an HP 15-ac121dx, It gets the error "System Board (00A) - System Board CT Number."


Now, when I click F1 to get the system information it says Ct Number: HP.
I have the correct CT number, but I'm trying to get the tools to be bootable from a flash drive so i can correct the information. I get it to work and when it comes up it ask me to correct the time, I do and it says Vendor code not supported or something along those lines. Is anyone willing to help me to see what I'm doing wrong?

Thank you!

[babypapa]

Re: HP DMI Tool NBDmiFit

thank's great post

[acshud]

Re: HP DMI Tool NBDmiFit

hy,i have hp probook x360 11 g3 ee and i was forced to rewrite the bios.now i don't have information about my laptop(sku,serial......) and when i turn on the laptop i have the message mpm.some advice?

[tlfrance]

Re: HP DMI Tool NBDmiFit

Hello,
On my elitebook 8460p, the sku / serial / CT .... numbers has get out of the bios. Don't know the reason . I've tryed many nbdmifit tool version from 1st page (HPSETxxx) of this thread without any luck. When i run the correct dmitool, i enter correct values from the laptop, then display the changes ans the end , but no changes seen from screen remains.
Anyone have already seen this issue?
I've done a bios dump with my programmer , but i'm not confident how to update this binary .
Thanks for help

[dreamteam]

Re: HP DMI Tool NBDmiFit

Which NbDmiFit do I use for Hp Elitebook 8540w?

[Slow]

Re: HP DMI Tool NBDmiFit

Can someone please recommend a version that supports HP Model 15-bs151ni.

[zedameo]

Re: HP DMI Tool NBDmiFit

thank you and god bless you

[SMDFlea]

Re: HP DMI Tool NBDmiFit

just name tell me name of programme so i can provide you proper backup.

When you get your bios dump, start a new thread in the bios requests section and post your bios there , please don`t post in this thread.

https://www.badcaps.net/forum/forumdisplay.php?f=40

[hassanulhaq]

Re: HP DMI Tool NBDmiFit

You need bios programmer read bios chip and post here.Other no have option you use toolkit is not proper your bios bkup..

just name tell me name of programme so i can provide you proper backup.

[imranromi]

Re: HP DMI Tool NBDmiFit

i hope you will provide bit guide too for bios flashing.

You need bios programmer read bios chip and post here.Other no have option you use toolkit is not proper your bios bkup..

[hassanulhaq]

Re: HP DMI Tool NBDmiFit

How to program bios if i send you?

i hope you will provide bit guide too for bios flashing.

[imranromi]

Re: HP DMI Tool NBDmiFit

i have attached the bios backup taken by Bios Backup tool kit. Please help me fix it.

How to program bios if i send you?

[hassanulhaq]

Re: HP DMI Tool NBDmiFit

Yes post here bios dump i will fix your error..

i have attached the bios backup taken by Bios Backup tool kit. Please help me fix it.

[SMDFlea]

Re: HP DMI Tool NBDmiFit

I have a HP Probook 450 G1 that used to have a admin password, I flashed the bios with a clean one to remove the password (using a ch341a).
After that I used the Wndmifit64.exe utility to program the serial number, sku and all that good stuff. after that I locked the mpm with the bat file. but I still have a the "Warning!! Machine is not in committed state". I did boot in EFI shell to run the startup.nsh but the it give me a "cannot determine ME capability". I also tried in dos, running the brand.bat, but it gives me a similar error.
I'm sure sure what to do next... any suggestions?

Clean the ME region.If you don`t know how to do it post your bios backup in the bios requests section for cleaning.

[GulagMaster]

Re: HP DMI Tool NBDmiFit

I have a HP Probook 450 G1 that used to have a admin password, I flashed the bios with a clean one to remove the password (using a ch341a).
After that I used the Wndmifit64.exe utility to program the serial number, sku and all that good stuff. after that I locked the mpm with the bat file. but I still have a the "Warning!! Machine is not in committed state". I did boot in EFI shell to run the startup.nsh but the it give me a "cannot determine ME capability". I also tried in dos, running the brand.bat, but it gives me a similar error.
I'm sure sure what to do next... any suggestions?

[imranromi]

Re: HP DMI Tool NBDmiFit

i have hp elitebook 2560p. Everytime i power on it gives me error product infromation is not valid and i have bios updated to f66 is there anny solution i tried v 2.13 also but didn't work for me. any solution?

Yes post here bios dump i will fix your error..

[hassanulhaq]

Re: HP DMI Tool NBDmiFit

i have hp elitebook 2560p. Everytime i power on it gives me error product infromation is not valid and i have bios updated to f66 is there anny solution i tried v 2.13 also but didn't work for me. any solution?

[dr.tubes]

Re: HP DMI Tool NBDmiFit

Hello,
I have a HP ProBook 650 G1 - when I start the laptop I am getting a message Product Information Not Valid. I know I am supposed to write the info manually, but I am not sure how. Which tool should I use to write the product info manually? I tried using HDMI tool and DR. Bios, but it's not working. MB manufacturer is Inventec.
Waiting for helpful advice...
Thanks

MPM is unlocked.

[cin]

Re: HP DMI Tool NBDmiFit

I was able to fix this by unlocking the MPM via nbdmifit uefi utility and then using HP BCU program located https://ftp.hp.com/pub/softpaq/sp100...0/sp100599.exe . I hope this helps someone and saves them some time!

[cin]

Re: HP DMI Tool NBDmiFit

Hi, I recently replaced a motherboard in a HP 24-B016 Pavilion AIO and it works great except the error message on boot up that it is missing product, serial, etc. I have tried the nbdmifit which I think is too old. I have also tried Wndmifit, but this says my board is not supported.

Anyone know which version / tool to use for this machine? Does the newest version of tool support all machines and older? I have tried 2.09 and 2.13. Thanks in advance!