I have 2 Pansonic CF-LX3EDKCS, One is Error ME Region,I have backed up to restore the fault but it still shows an error as tiltle
Help me to create a bios to fix error. Thank you
Help me to create a bios to fix error. Thank you
-
-
↵
Any donations to badcaps are welcome, click this link to donate . Thanks to all the supporters
https://www.badcaps.net/donate -
SN: 4AKSA18080
Thank You!Attached Filesif you find these attachements useful please consider making a small donation to the site
Comment
-
-
Hi Shiyab, i tried and still got error!
I have backed up the bios file of the Laptop with SN 4AKSA25684 to restore the faulty laptopAttached Filesif you find these attachements useful please consider making a small donation to the site
Comment
-
-
I have a T490 that displays the error message “2203: System configuration is invalid” immediately after the Lenovo logo every time it boots up.
This message must be acknowledged with 'Esc'. On the one hand, I cannot eliminate the problem, on the other hand, I have not observed any other restrictions.
Is it possible to change the BIOS so that this message no longer has to be acknowledged?
MTM 20N3S19L00
system SN PF1X4JP8
board SN L1HF171000X... -
Hi all!
HISENSE 65E7KQ PRO
RSAG7.820.13512 - chassis
MT9618BAATAB - cpu
RSAG7.820.12059 - power
HD650Y3U77 - panel
KLM8G1GETF - emmc
The TV does not turn on, the standby indicator is on. All voltages are present.
Emms is dead. Not readable, not detected.
Replaced emmc.
But with another dump there is no launch
Terminal log
UART
<
AC_ON
RPMB key is not yet programmed
HASH1_VERSION=0x00000000 64bit
E-B
FDE enabled
layout pattern onebin by SAR7,0... -
one of our new (only 4 year old) 1KVA APC UPS stop working and through error P13 contact customer support.
the equipment is out of warranty , upon investigation, we found the inverter board has the fault on the output hybrid relay circuit.
The inverter output relay is parallel by SCR/Triac to enhance the relay performance or other means.
We replaced the SCR with new device,, but the device is not power on as expected.
Further research on the issue found that, the error P13 (event ID 107) is latched on the UPS nvram/MCU and need to clear/reset using a service procedure....09-26-2025, 09:00 AM -
Hi,
Has anyone come across the attached error message whilst using CSME System Tools v16.0 r3.
I've just loaded up an XML generated from the same application, and the error appears with no real clue as to how to fix it:
Exception: Error occurred whilst trying to create container CseRegion. Reason Mismatch between CSE version and layout project version
Layout Accepts: 16.0.x.y
CseVersion: 16.1.25.2128
Source: CsePlugin: CseRegion
Source: CsePlugin
Thanks in advance (hopefully someone knows....)... -
Hello Sharp TV experts
Our Sharp LC-80LE642U displays one short one long flash error code which is a backlight error. I went into service mode and there were 8 lamp error counts recorded. I reset the count to 0 and did a reset. The last monitor error cause was 16 B00014639:12. 16 is the code for backlight error. I tried to power the tv up but went back into error mode.
> I checked voltages on the power supply board and they all check out .. including 3.28 volts at the error pin.
> There is power to the cpu and T-CONN and no faults found there. The cpu has a flashing...01-24-2025, 11:51 PM
Comment