bucks_UMA-MB 16872-1 Can You Help me?

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • REBZ
    New Member
    • Jan 2022
    • 5
    • México
    #1

    bucks_UMA-MB 16872-1 Can You Help me?

    Buenas noches. Solicito su ayuda. Alguien que pudiera proporcionar los valores y ubicacion de los siguientes componentes.
    es un controlador de Vcore. Anexo mediciones y datasheet.
    No encontre diagrama alguno que use este ic

    Good evening. I need your help. Someone who could provide the values and location of the following components.
    it is a vcore controller. Annex measurements and datasheet.
    I did not find any diagram that uses this ic

    bucks_UMA-MB
    16872-1
    448.0C204.0011
    HP 14-BA004LA
    Attached Files
    Last edited by REBZ; 02-22-2022, 07:47 PM. Reason: Idioma-Language
    Tags: None
    • mcplslg123
      Badcaps Legend
      • Jun 2015
      • 7262
      • india
      #2
      Re: Can You Help me?

      Here is the screenshot for relevant part.
      Attached Files

        Comment

        • REBZ
          New Member
          • Jan 2022
          • 5
          • México
          #3
          Re: Can You Help me?

          thanks so much. exactly i needed!!!

            Comment

            • mcplslg123
              Badcaps Legend
              • Jun 2015
              • 7262
              • india
              #4
              Re: Can You Help me?

              Originally posted by REBZ
              thanks so much. exactly i needed!!!
              That's the motto of badcaps community. Helping each other.

                Comment

                • tavito
                  Member
                  • Nov 2013
                  • 10
                  • Argentina
                  #5
                  Re: Can You Help me?

                  May you upload the schematic please. Thank you

                    Comment

                    • SMDFlea
                      Super Moderator
                      • Jan 2018
                      • 20309
                      • UK
                      #6
                      Re: Can You Help me?

                      Originally posted by tavito
                      May you upload the schematic please. Thank you
                      All schematic requests should be made in the "Schematic requests ONLY!" sub forum -> https://www.badcaps.net/forum/forumdisplay.php?f=41
                      A request has already been made you can add your own request to the same thread -> https://www.badcaps.net/forum/showthread.php?t=75871

                      .
                      All donations to badcaps are welcome, click on this link to donate. Thanks to all supporters

                        Comment

                        Previous template Next

                        Related Topics

                        Collapse
                        • Francisco.s
                          CPU vcore missing in HP workstation Z2 Mini 4G
                          by Francisco.s
                          Hi, have a HP workstation Z2 Mini 4G for repair with CPU vcore missing.

                          The resistance at the output of CPU vcore coils, is less than one ohm so I think CPU could be damaged, but no mosfet are damaged.
                          It mounts an i7 8th gen, and have only i5 7th gen for test, but I think it is not compatible.

                          Without CPU in the socket there is no short, but there is no vcore voltag, and it emits a beep like no detecting ram.

                          The controller chip for cpu vcore is a MP2949A, and has no enable voltage at pin 37.

                          I wonder which circuit generates this enable...
                          04-22-2024, 12:35 PM
                        • mikzs
                          Rx580 8gb sapphire nitro+ turn off vcore randomly
                          by mikzs
                          Hello, this is my first post, English is not my native language but I hope you understand me. I recently got a 580 that didn't turn on the typical short mosfet, as I didn't know exactly which one was short, I unsoldered them until I got the bad one out, I was able to remove the short and identify the bad mosfet, the gpu gives video again! but it has a problem that completely turns off vcore at random times or if I try to put a load on the gpu vcore drops to 0 I don't have much idea why because I don't know much about sapphire, any advice on where I could start looking or what problem it could...
                          11-06-2023, 12:28 PM
                        • jm942
                          Hp Lh482p 5 short 3 long short after cpu vcore mosfet replacement
                          by jm942
                          Hi,
                          My laptop went dead and after checking ,the main 19 volt power rail was shorted. After some checks i could identify that a high side vcore mosfet was shorted.
                          I replaced the mosfet and now the white powerled is present , fans start spinning but capslock shows the famous 5 long and 3 short code.

                          I checked the vcore voltages after replacement and i get for all 1.01 V so means for me that the driver is still working of the replaced shorted mosfet. On the Nvidia i measure around 0.8 V after the mosfets.
                          I did voltage injection on the cpu with 0.7V and i have a current...
                          07-11-2024, 05:11 AM
                        • kotel studios
                          Epox EP 85 MVP3C-M - 3.54v Vcore regardless of jumpers
                          by kotel studios
                          Hi,

                          Recently I got an Epox EP-85 MVP3C-M board from scrap. After fixing the broken caps I powered it on without CPU and the jumpers set to 60Mhz FSB and 2x multiplier.
                          Sadly, Vcc3 was stuck at 3.54v regardless of jumpers. Vcc2 (Vi/o I think) was also the same voltage.
                          So, I've returned to the original configuration I got the board in - 100Mhz FSB and 4x multiplier. Voltages haven't changed at all.
                          What I've tried so far:
                          replace the original N-MOSFETs with beefier 60V ones for testing
                          Resolder the resistors near the Vcore Jumper block
                          Short Vcore...
                          05-25-2025, 01:46 AM
                        • stephtech
                          GTX1060 not working, Vcore down to 0.3V
                          by stephtech
                          Hi,
                          Need some help as I am struggling with this GPU.
                          It is an Asus Dual GTX 1060 3GB

                          Current problem when I received the board (I do not know previous history), device manager show error code 43. GPU-Z show UNKNOW in Bus Interface (PCIe speed), no display. GPU-Z show all the infos for the board, only unknown for the bus interface.

                          Steps I took:

                          1- Disassembled the gpu and physically inspected everything on the board. No missing components, no shorts, no burnt marks, all looks normal. No open 0 ohms resistors.

                          2- connected...
                          01-15-2022, 11:10 PM
                        • Loading...
                        • No more items.
                        Working...