hp DV6, turn offf after 2sec. no CPU power, only 0,5V ECPWROK signal

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • ktmmotocross
    Boardkiller
    • Feb 2014
    • 3577
    • slovakia
    #21
    Re: hp DV6, turn offf after 2sec. no CPU power, only 0,5V ECPWROK signal

    and i found that when processor not work the SDCARD LED light. when procesor work the SDCARD LED shuts down

      Comment

      • dj_ricoh
        Badcaps Legend
        • Jan 2013
        • 2073
        • uk
        #22
        Re: hp DV6, turn offf after 2sec. no CPU power, only 0,5V ECPWROK signal

        Omg! Very nice .
        Now i know why my oven works like a charm. Hehehehe
        Just cook it! It's already broken.

          Comment

          • highpulse
            i hate HP
            • May 2013
            • 1488
            • portugal
            #23
            Re: hp DV6, turn offf after 2sec. no CPU power, only 0,5V ECPWROK signal

            well , still becarefull , you reflowed a bit the socket , board got hot in several places , like i mentioned before , bad contact on bus between cpu and MCP , chek carefully

            yes sdcard LED when shut off its means he passed the pre post before bios .
            usually if led stay light problem on northbridge or cpu

              Comment

              Previous 1 2 template Next

              Related Topics

              Collapse
              • AstutePauciloquent
                Requesting Help For GA-970A-DS3 rev. 1.0, No Post code, no RSMRST# signal
                by AstutePauciloquent
                Hi everyone, over the past few months i have taken a deep dive into motherboard diagnostics and I love the challenge. Currently im trying to learn all about the signals that travel around the motherboard, such as frequencies, enable signals High and Low logic states etc. And i have been learning to read and using the Schematics for this board that i requested here on Badcaps forum, from a few months ago, this is such a great place for these.

                I’ve been working on a GA-970A-DS3 (rev. 1.0) that does not post. This motherboard has been my main learning board. I would like share...
                11-23-2023, 11:02 PM
              • howardc64
                Vizio M65Q7-H1 Red Vertical Strips fixed by tape blocking LC1 signal to half of the panel
                by howardc64
                Failure Symptom



                No picture, just red vertical stripes. Google search shows quite common problem for these recent Vizio M series although red vertical stripe pattern may differ. Some call it "Netflix" boot screen haha.

                Where is the short?

                Panel has 4x buffer boards. Quickly found the 1/4 panel buffer board with the problem by selectively disconnecting buffer board flex cables.



                Having recently fixed another Vizio with similar symptoms that was a shorted ESD diode array ( link ) Probed the ESD diode array but...
                05-27-2025, 02:56 PM
              • JayPoorJay
                Converting +/- 5v to a Usable Hz Signal
                by JayPoorJay
                Good morning.

                I have posted here before and have gotten AMAZING advise (thank you!). I'm back for more. This BCaps Sub Forum is so well attended I thought I would post here.

                This question is for an automotive application but has to do with what are essentially electrical questions and problem solving... If this is inappropriate I get it. Feel free to delete it or move the question.

                The V 12 Jaguar XJS is notorious for overheating in stop and go traffic in hot weather... Y'all will be potentially helpinh a LOT of people. The solutions and directions...
                08-07-2022, 08:35 AM
              • Scruit
                What is a normal composite signal range for a C64?
                by Scruit
                Hello all,


                Working on my first C64 / Breadbin / 250407. Purchased as non-working. Getting black screen.


                More detail below, but for those that want to get right to the question.... Here are a few waveforms comparing the Pin15 output on the VIC chip (luma/sync) to the pin 4 on the AV socket (composite signal).

                https://imgur.com/gallery/PpqcqPY


                My question is: Is the composite waveform range of 0.1v-1v too low for a c64?



                More detail:


                Symptoms are that that I get...
                04-28-2022, 05:33 AM
              • supravit2000
                PS4 fat has inconsistent signal after HDMI replacement
                by supravit2000
                Hi, guys!

                I am not a professional, all I can do is solder stuff on the boards, so I would really appreciate it if someone with knowledge shares his experience/thoughts on a problem I have with a PS4 console.

                My friend gave me an original fat PS4, board model SAB-001, with WLOD, that has been previously opened. I changed the HDMI port, couple of pads on the board were ripped, which I connected to the corresponding caps/resistors? Just did so as in a shown diagram (one of the ground pads I ripped off and left it not connected). However, there was still no signal, so...
                12-19-2022, 08:08 PM
              • Loading...
              • No more items.
              Working...