Try our *UPDATED* boardview, bios, & schematic search. Over 2.3 million files for download!

GPU power rail short circuit (likely blown MLCC capacitor) – ASUS TUF FX506IU (Quanta BKXB)

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Remus96
    • Sep 2026
    • 6
    • Hungary

    #1

    GPU power rail short circuit (likely blown MLCC capacitor) – ASUS TUF FX506IU (Quanta BKXB)

    Hi everyone,I ran into an issue where my ASUS TUF FX506IU suddenly shut down and wouldn't power back on. Despite only having basic electronics knowledge, I decided to diagnose the board myself.
    So far, I've tracked down the issue to a short on the GPU power rail. After desoldering the PR524 current shunt resistor to isolate the GPU circuit, the main VIN rail cleared up (no beep/open circuit to ground on the VIN pad in continuity mode). However, the short to ground is still present on the VIN_GPU side.
    Visually, none of the ceramic capacitors (MLCC) appear damaged, cracked, or discolored. Since I don't have a DC lab bench power supply for thermal/voltage injection and my multimeter reads ~0.2 Ω across all parallel caps due to the copper planes, how can I pinpoint the specific shorted component without desoldering every single one?
    Any tips or best practices would be greatly appreciated!
    Thanks in advance!

    Schematic:
    https://www.badcaps.net/forum/troubl...72#post1762472

    Boardview:
    https://www.badcaps.net/forum/troubl...75#post3491475
    ​​​​​
  • reformatt
    Badcaps Legend
    • Feb 2020
    • 1832
    • Australia

    #2
    GPU power inputs often measure close to 0, that's normal. Very likely one of the NVVDD MOSFET's has shorted (PQ56~PQ58). Highly advisable to replace the associated driver IC (PU25~PU27) with it when that happens. Unlike CPU FET failure, the GPU seems to survive these events.

    You could do 1V or lower voltage injection and use IPA to see which MOSFET it is if you don't have a thermal camera. If you are concerned about protecting the GPU, then short the +NVVDD power rail to ground for your injection.

    Comment

    • Remus96
      • Sep 2026
      • 6
      • Hungary

      #3
      Thanks man, you are awesome!! Thanks a lot, really! I'm about to do the measurements now—managed to get hold of a power supply, so hopefully I'll find the fault. One quick question: once I locate the bad component and remove it, but before soldering in a replacement, how can I tell if any other components were damaged as well?
      Thanks in advance for your help!

      Comment

      • reformatt
        Badcaps Legend
        • Feb 2020
        • 1832
        • Australia

        #4
        It's usually only one of the phases that fails so confine measurements to that. Driver IC replacement in the failed phase is highly recommended as the replacement MOSFET can fail instantly on power up. Chicken and egg situation. Did the driver fail and cause the MOSFET to fail, or the other way round? If both fail again you then have to replace the PWM IC as well.

        Comment

        • Remus96
          • Sep 2026
          • 6
          • Hungary

          #5
          Thank you very much for the help so far! I managed to detect and replace the faulty MOSFET and its associated driver IC—it was quite a struggle, but I got it done.

          I would like to ask about another issue I've run into: I'm measuring barely any voltage at the battery (around 0.9 volts), yet the laptop indicates it's fully charged. Now, could it be possible that a cell failed and the BMS (Battery Management System, if I got the name right) triggered a lockout? How could I check or verify this?

          ​Thanks in advance for your answers!
          ​

          Comment

          • Remus96
            • Sep 2026
            • 6
            • Hungary

            #6
            Also, as some extra info: the IC was very difficult to get off—it was around the PU26 area—and by accident, I also took off PU25 along with it (I didn't tear any pads, I just looked at the wrong spot at first). Since the board had already been through a lot, instead of putting the original back, I ended up replacing both PU25 and PU26 along with the faulty PQ26 MOSFET. Now, I had to heat it quite a few times, and even on the new component, the package got a little bit heat-stressed, but the laptop is working fine even under load. Do I need to worry about any of this?

            Comment

            Related Topics

            Collapse

            • User 4574
              Asus , board 532lws R1..3 Power rail 5v , 3v dsw
              by User 4574
              Hi everyone .
              I have model g712l And In stuck.
              Originally this laptop has a short on main Power rail . Thé main short is gone, i have found 2 pea16b mosfets Next to the SN51285ARUKR shorted , and the Chip Intself was Also shorted , i have removed them and main Power rail IS not shorted anymore , but right Now im still eating for this parts And in checking rest of the board . But pin 14 od the SN51285ARUKR when this chip od removed is shorted to ground Its +5VSUS has 6ohms , And that can not be , i have check mosfets All over the board And i have found ONLY one tahat ís shorted its...
              Bad cap
              0%
              0
              Shorted internal layer in thé motherboard
              0%
              0
              06-21-2026, 07:50 AM
            • Nagy Daniel
              Lowest possible resistance on laptop motherboard rail - Guide Table request
              by Nagy Daniel
              Hi, I'm Daniel, and I'm new to the world of repairing motherboards.

              I would like to create a table, or more likely a guideline about the voltage rails and their possible resistance rail.

              I know that the motherboard design has a very big depend on the rail's resistance, but I would like to know what is the smallest value for a rail that can be acceptable. For example, I heard that some new gaming motherboards can have 0,5 Ohm resistance on the GPU rail, but on an older type, it could be a sign of a shorted GPU rail.

              So, I generated a table with AI so I can...
              03-04-2025, 08:24 AM
            • Boardview and Schematic Bot
              ASUS TUF Gaming FX506IU-AL016 Notebook Specification for Upgrade or Repair
              by Boardview and Schematic Bot
              This specification for the ASUS TUF Gaming FX506IU-AL016 Notebook can be useful for upgrading or repairing a laptop that is not working. As a community we are working through our specifications to add valuable data like the FX506IU-AL016 boardview and FX506IU-AL016 schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties that any specification, datasheet, or download...
              09-06-2024, 08:40 PM
            • Boardview and Schematic Bot
              ASUS TUF Gaming FX506IU-AL014 Notebook Specification for Upgrade or Repair
              by Boardview and Schematic Bot
              This specification for the ASUS TUF Gaming FX506IU-AL014 Notebook can be useful for upgrading or repairing a laptop that is not working. As a community we are working through our specifications to add valuable data like the FX506IU-AL014 boardview and FX506IU-AL014 schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties that any specification, datasheet, or download...
              09-06-2024, 08:10 PM
            • Boardview and Schematic Bot
              ASUS TUF Gaming FX506IU-BQ225 Notebook Specification for Upgrade or Repair
              by Boardview and Schematic Bot
              This specification for the ASUS TUF Gaming FX506IU-BQ225 Notebook can be useful for upgrading or repairing a laptop that is not working. As a community we are working through our specifications to add valuable data like the FX506IU-BQ225 boardview and FX506IU-BQ225 schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties that any specification, datasheet, or download...
              09-06-2024, 06:50 PM
            • Loading...
            • No more items.
            Working...