Hello.. any help is appreciated.
Alienware m15 R7 LA-L651P completely dead, RSMRST# stays low
I’m working on an Alienware m15 R7, board HDQ50 LA-L651P Rev 1.0. It is completely dead: no LEDs, fan movement, charging light or response to the power button. Original Dell adapter stays on.
Measurements with adapter connected:
- 19 V input
- +3VALW and +5VALW present
- +VCCIN_AUX: 1.8 V
- +VCCDSW_1P05: 1.10 V
- +1.8VALW_EC: 1.8 V
- EC AVCC: 3.3 V
- +3VLP_VSBY: 3.3 V
- +RTC_CELL / RTC_CELL_VBAT: 3.08 V
- EC_RESET#: 3.42 V
- SRTCRST#: 3.04 V
- ACOK: 3.27 V
- PCH_DPWROK_EC: 3.11 V
- PRIM_PWRGD: 3.38 V
- VCCIN_AUX_VR_PG: 3.38 V
- 1.8V_PRIM_PG: 3.3 V
- SIO_PWRBTN#: about 2.8 V idle, drops to 0 V when pressed
The problem is:
- PCH_RSMRST#: 0 V
- PCH_RSMRST#_R: 0 V
- PCH_RSMRST#_AND: 0 V
- PCH_RSMRST#_AND_POK: 0 V
- PM_RSMRST_PWRGD_MIPI60: 0 V
Resistance from PCH_RSMRST#_R to ground is about 100 kΩ, matching the schematic pull-down. RE177 between PCH_SUSCLK and SUSCLK_EC measures 0 Ω.
I read and verified the original 32 MB W25Q256 dump. I also flashed and verified a full LA-L651P donor image, with no change at all. The board uses EC G3 flash sharing with the main SPI.
I only have a multimeter, thermal camera, CH341A, schematic and boardview—no oscilloscope yet.
What should I check next that could prevent the NPCX996 from releasing PCH_RSMRST#?
Schematic/boardview - https://www.badcaps.net/forum/troubl...36#post3724636
Alienware m15 R7 LA-L651P completely dead, RSMRST# stays low
I’m working on an Alienware m15 R7, board HDQ50 LA-L651P Rev 1.0. It is completely dead: no LEDs, fan movement, charging light or response to the power button. Original Dell adapter stays on.
Measurements with adapter connected:
- 19 V input
- +3VALW and +5VALW present
- +VCCIN_AUX: 1.8 V
- +VCCDSW_1P05: 1.10 V
- +1.8VALW_EC: 1.8 V
- EC AVCC: 3.3 V
- +3VLP_VSBY: 3.3 V
- +RTC_CELL / RTC_CELL_VBAT: 3.08 V
- EC_RESET#: 3.42 V
- SRTCRST#: 3.04 V
- ACOK: 3.27 V
- PCH_DPWROK_EC: 3.11 V
- PRIM_PWRGD: 3.38 V
- VCCIN_AUX_VR_PG: 3.38 V
- 1.8V_PRIM_PG: 3.3 V
- SIO_PWRBTN#: about 2.8 V idle, drops to 0 V when pressed
The problem is:
- PCH_RSMRST#: 0 V
- PCH_RSMRST#_R: 0 V
- PCH_RSMRST#_AND: 0 V
- PCH_RSMRST#_AND_POK: 0 V
- PM_RSMRST_PWRGD_MIPI60: 0 V
Resistance from PCH_RSMRST#_R to ground is about 100 kΩ, matching the schematic pull-down. RE177 between PCH_SUSCLK and SUSCLK_EC measures 0 Ω.
I read and verified the original 32 MB W25Q256 dump. I also flashed and verified a full LA-L651P donor image, with no change at all. The board uses EC G3 flash sharing with the main SPI.
I only have a multimeter, thermal camera, CH341A, schematic and boardview—no oscilloscope yet.
What should I check next that could prevent the NPCX996 from releasing PCH_RSMRST#?
Schematic/boardview - https://www.badcaps.net/forum/troubl...36#post3724636
Comment