any body knows how to remove smart error on hdd
hdd smart error
Collapse
X
-
Re: hdd smart error
You can't really remove a SMART error from an HDD. SMART is supposed to give you a heads up about imminent HDD failure.
Whenever a HDD gives you a SMART errors the first step is always to image the HDD or back it up manually if you are not familiar with imaging. Once that's done I normally either send it out for warranty replacement if applicable or use it for none critical data until it kicks the bucket.Comment
-
Re: hdd smart error
smart can be erased but its very complicated... seagate disks can be doable with terminal like this
https://sites.google.com/site/seagatefix/Home
http://forum.hddguru.com/viewtopic.php?t=11040&start
rest of them need special card calld pc3000
http://www.acelaboratory.com/
enter this
CRTL+Z
F3 2>U
Spin Up Complete
Elapsed Time 7.242 secs
F3 2>
F3 T>/1
F3 1>N1
this is a S.M.A.R.T. erase
after that POWER off HDD, it means that you plug off power to hdd,
power on hdd,
reenter
CTRL+Z on terminal
F3 T>i4,1,22
this is G-list erase
after that POWER off HDD, it means that you plug off power to hdd,Last edited by ala_borbe; 02-24-2014, 04:00 AM.Im Back... sort of...Comment
-
Re: hdd smart error
Surely won't the error just return? What error is it?Dell E7450 | i5-5300U | 16GB DDR3 | 256GB SSDComment
Related Topics
Collapse
-
by Sus256Hi all!
HISENSE 65E7KQ PRO
RSAG7.820.13512 - chassis
MT9618BAATAB - cpu
RSAG7.820.12059 - power
HD650Y3U77 - panel
KLM8G1GETF - emmc
The TV does not turn on, the standby indicator is on. All voltages are present.
Emms is dead. Not readable, not detected.
Replaced emmc.
But with another dump there is no launch
Terminal log
UART
<
AC_ON
RPMB key is not yet programmed
HASH1_VERSION=0x00000000 64bit
E-B
FDE enabled
layout pattern onebin by SAR7,0... -
by hakuuartHello everyone, I need some help or advice regarding the HP Smart Tank 750 device. I have already checked for paper jams and anything stuck inside, as well as all the flex cables, but I still encounter an E4 error. We have taken it to customer service for inspection, but they don't know how to fix it. Is it possible that the issue lies with the main board or the sensor? I would really appreciate any guidance from those who have experienced this problem. Thank you!...
-
by Superbee_dadHello Sharp TV experts
Our Sharp LC-80LE642U displays one short one long flash error code which is a backlight error. I went into service mode and there were 8 lamp error counts recorded. I reset the count to 0 and did a reset. The last monitor error cause was 16 B00014639:12. 16 is the code for backlight error. I tried to power the tv up but went back into error mode.
> I checked voltages on the power supply board and they all check out .. including 3.28 volts at the error pin.
> There is power to the cpu and T-CONN and no faults found there. The cpu has a flashing...01-24-2025, 11:51 PM -
by MaalobsHi,
I have a 2014 vintage Philips 60PFL8708S/12 that suddenly died in the middle of the kids watching a show.
The relevant service manual for the chassis is available here.
The TV no longer powers on, and leaving it powered on for a few minutes results in the layer-1 error with 2 blinks.
When I short the SDM to ground I get the layer-2 error code 53.
The inside of the TV has no damaged components and no swollen capacitors.
In SDM-mode when all the power rails are left on despite entering the protection mode, I tracked down and measured... -
by medinfoMacbook Pro 2019 T2
iCloud OFF
MDM unlocked by changing Serial Number
worked fine but after latest update see (There was an error activating your device. Please try again).
Erased and boot in internet recovery, same error.
changed to original serial number (iCloud OFF & MDM ON), same error.
tested with others serial number, same error.
tested (CMD+R), (Option+CMD+R), (Shift+Option+CMD+R), same error
Revived and restored by Apple Configurator and same error.
Any help ?1 Photo - Loading...
- No more items.
Comment