Packard Bell Kayfo, no picture on screen.

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • nasdaa
    New Member
    • May 2023
    • 6
    • France

    #1

    Packard Bell Kayfo, no picture on screen.

    Hello, I need your help for a failure on a laptop:

    It's a Packard Bell Kayf0, motherboard LA-5021P, Rev 1.0 with graphic issue.

    I received this pc because it was turning on but not displaying anything, the fans are running normally and all chipsets heat up on startup but no picture on screen, no backlight either. I noticed that ENAVDD and ENVDD are not present and that there is no LCDVDD on the connector. I didn't check the screen because, maybe I'm wrong, but if there aren't these signals, even if the screen is good, it can't display anything? I tried heating the gpu for 1min30 with the hot air gun but still nothing, apart from an increase in total current from 800 mA to 1 A, the GPU coil shows 5 ohms at ground. Tell me if it's useless, but I removed the R283 to measure the signal sent by the GPU before the jumper and it's still 0v on both sides, does this mean that neither the GPU nor the screen wants to activate the screen? Also, can the GPU chipset get hot even if it's defective?

    Thanks for your answers.

    Schematic: https://www.badcaps.net/forum/showth...61#post1248261
    Last edited by Vesko356; 06-20-2023, 01:56 AM. Reason: Attached schematic removed and replaced with link.
  • nasdaa
    New Member
    • May 2023
    • 6
    • France

    #2
    Re: Packard Bell Kayfo, no picture on screen.

    Any ideas ?

    Comment

    • Stevedb
      Stevedb
      • Feb 2018
      • 624
      • Belgium

      #3
      Re: Packard Bell Kayfo, no picture on screen.

      Are you certain the board is posted, does capslock react or can you do ctr alt del and laptop reboots?

      Comment

      • nasdaa
        New Member
        • May 2023
        • 6
        • France

        #4
        Re: Packard Bell Kayfo, no picture on screen.

        I managed to burn an ic by trying to power the screen, and i've spend too much time on this board so i give up but thank you for your time ! Also, does the capslock reacting necessary means that the board is posted ?

        Comment

        • Stevedb
          Stevedb
          • Feb 2018
          • 624
          • Belgium

          #5
          Re: Packard Bell Kayfo, no picture on screen.

          Yes then you know if the board is posted and fullfill all recomdations to post.

          Which ic blew up?

          Comment

          • nasdaa
            New Member
            • May 2023
            • 6
            • France

            #6
            Re: Packard Bell Kayfo, no picture on screen.

            Oh ok now its clearer. When i plug the charger there is an additonnal 500mA consumption and the Clock Generator (U3) is getting very hot so i think it's shorted, but i can't find the datasheet online so that's it. Have a nice day.

            Comment

            • mon2
              Badcaps Legend
              • Dec 2019
              • 14182
              • Canada

              #7
              Re: Packard Bell Kayfo, no picture on screen.

              Just found this amazing item on AliExpress. Check it out! US $2.16 | 1pcs/lot New SLG8SP553V QFN
              https://a.aliexpress.com/_mqMP2ZW

              Comment

              Related Topics

              Collapse

              • Mgiffune
                Samsung UN60EH6000F Black Screen, Backlight and Sound Good. Power Cycle Returns Picture
                by Mgiffune
                I have a 60 inch Samsung UN60EH6000F flatscreen TV. The screen went black a few months ago Sound is good, backlight is good, no menu. I replaced the TCon board with a used board purchased from Ebay. It worked fine for a 3-4 months, then the screen started ‘fading' back. Once again, sound is good, backlight is good, no menu. However, this time the picture looks fine for about 10-15 minutes, then fades back. If I power cycle the TV, the display reappears, for another 10-15 minutes, then fades black again. Repeatable ever time.

                I ordered a supposedly ‘new' Tcon board this time, and
                ...
                06-09-2024, 10:28 AM
              • Ryan.man
                Macbook 2017 with touchbar (A1706) won't turn on after removing the screen
                by Ryan.man
                Hello everybody! Posting this in hopes somebody has some expertise that leads to a clear path of troubleshooting that saves me a lot of time!

                My macbook has the flex cable problem, the one that prevents the screen turning on. Ive been dealing with this for the last 3 years. Last year it went dead and I managed to fix it following youtube tutorials. But my fix wasnt the best, the problem returned a month later. This week, it went dead again. I again tried to fix it.

                This time the original cable broke too close to the screen, it can't be fixed without tearing the screen...
                02-04-2025, 12:23 PM
              • maxlove70
                Need Bios Packard Bell iSTART 2356
                by maxlove70
                Hello, I'm searching Bios for Packard Bell iSTART 2356.

                Asus for Packard Bell M2NS-NVM (Boston) 0206 BIOS - 6A69NA01
                Manufacturer and model: Asus for Packard Bell M2NS-NVM (Boston)

                Chipset: AMD 1100

                Part number: 6A69NA01

                BIOS ID: 03/05/2007-NF-MCP61-M2NS-NVM-00

                BIOS Release date: 2007-03-05

                BIOS Revision: 0206


                Packard Bell Support for this PC is discontinued.
                Please Help Me !!!!

                Thanks.
                02-16-2023, 11:52 AM
              • arbitarytwist
                Samsung UN50NU7400 - No Picture (but boot screen and screensaver)
                by arbitarytwist
                Have a Samsung UN50NU7400 which shows a boot screen and a screen saver if left on long enough but no picture ?

                Would a moving screen saver confirm that the panel is ok or it could still be a panel issue ?
                03-01-2025, 01:16 PM
              • reformatt
                Macbook Air M2 A2681 Kernel panics after screen replacement
                by reformatt
                Just had a customer bring in a M2 MBA A2681 that had had a screen replacement in April at another repairer. Since then, she has been getting intermittent kernel panics. It's an aftermarket screen, and of course it fails in diagnostics as the calibration hasn't been done. The error in the panic log is "No device added after powering on the rails".

                It seems the original repairer has swapped the board and the screen to other MAC's, and said that it isn't a screen issue. From what I understand, by doing a quick search on Google, this is in fact a screen issue. The panic relates...
                07-31-2025, 08:37 PM
              • Loading...
              • No more items.
              Working...