PS5 Disk Tray issues.

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • welp
    New Member
    • Apr 2024
    • 3
    • USA

    #1

    PS5 Disk Tray issues.

    I have a PlayStation 5 CH-1215A with a Disk drive not reading disks anymore. (accepting and ejecting very slowly.)
    Knowing the PS5 has a married daughter board for the disk drive I made sure to use that and replace the rest of the disk tray as it* was owned previously by an indoor smoker.
    Once the job was complete and put back everything together, I tried to insert a disk with no luck at all...
    So, I checked voltage going from the ps5 to the daughter board and am only getting the 5V rail.
    With that knowledge I preceded to check all the fuses for the 12v rail on the main board, all fuse's check out.

    Where should I look next?
  • welp
    New Member
    • Apr 2024
    • 3
    • USA

    #2
    Fuse was blown on the 12V right before the power connector for the disk tray.

    Comment

    Related Topics

    Collapse

    • Document Archive
      Surface Mount Fuses Fundamentals Datasheet
      by Document Archive
      TE Circuit Protection offers the widest selection of surface-mount fuses available for addressing a broad range of overcurrent protection applications. Helping to prevent costly damage and promote a safe environment for electronic and electrical equipment, our single-use chip fuses provide performance stability to support applications with current ratings from .5A up to 20A.

      TE Circuit Protection also offers the telecom FT600 fuse for telecommunications applications. This telecom fuse helps comply with North American overcurrent protection requirements, including Telcordia, GR-1089,...
      10-07-2024, 06:07 AM
    • nervous_capybara
      Repairing the Hitachi DA-6000 CD player
      by nervous_capybara
      Hello everyone !

      I recently conducted maintenance on a Hitachi DA-6000 CD player for my grandparents : it had two distinct issues.
      Feel free to share your experience if you ran into other issues.

      DISCLAIMER : BE VERY CAREFULL WHEN OPERATING ON THIS SYSTEM : THE HIGH VOLTAGE IS VERY CLOSE TO THE VARIOUS TESTING POINTS, PROCEED WITH CAUTION

      CD tray would not come out of the player
      I could hear a motor spinning inside the player but the CD tray would not come out.
      Turned out that the issue was the CD tray belt that aged poorly and began to...
      11-05-2025, 03:11 AM
    • Sik_6ty_Sixx
      HH Scott Model A510 Stereo Integrated Amplifier/ Graphic EQ - Blowing fuses in the LEFT speaker channel only. Any Help???
      by Sik_6ty_Sixx
      So like the title says, I have an old Stereo Receiver/Amplifier that I picked up from the goodwill, it's a HH Scott Model A510. When I first got it home it had zero output. Opened it up, notice the fuses are missing. Pop in 2 new fuses (AGC4A 250V) and try again, within 5 seconds the L channel fuse POP! I don't see any visible indications of damage or arc burns on the PCB, no popped resistors or diodes, no burnt traces or blown out caps. So I decide to just try another new fuse, POP. Swapped around my R and L speaker wires, and checked the integrity of all wires and connections. Everything looks...
      02-18-2025, 05:06 AM
    • DynaxSC
      ASUS ROG STRIX B550-I GAMING - M.2_2 port not working correctly with SAMSUNG SSD980 1TB NVME SSD
      by DynaxSC
      Hi,

      I have an really very weired issue with ASUS ROG STRIX B550-I GAMING.

      Some NVME (PCIe) SSD's are not working correctly in the second M.2 socket. An example of it is the SAMSUNG SSD980 1TB NVME SSD.
      Some other NVME (I have only smaller ones) disk do work without any problem, also SAMSUNG disks, eg an MZVPV128HDGM-0000.

      The behaviour is also really very strange, i.e.:
      • The disk shows always up in BIOS - so it is recognized, so far so good
      • POST-ing with this disk with fresh Windows 24H2 installation (done in the M.2_1 socket) in the M.2_2 socket
      ...
      02-23-2025, 01:33 PM
    • Stanley1843
      Windows 11 disk no boot
      by Stanley1843
      I tried to install Linux on a secondary disk in my PC and after a failed Linux grub installation my PC didn't boot in Windows 11. I saw the message (Reboot and select a proper Boot device).

      I made a bootable USB windows 11 and I run the below commands on the cmd but with no succeed.

      DISM /Online /Cleanup-image /Restorehealth
      The DISM.... command shows me the error 87.

      sfc /scannow
      chkdsk

      bootrec /FixBoot
      bootrec /ScanOs
      bootrec /RebuildBcd
      For some reason it writes(Total identified installations 0) like there no...
      10-18-2025, 04:41 AM
    • Loading...
    • No more items.
    Working...