Does anyone have any tips on how to properly remove the capacitors that are attached to the cool stack board on my Asus P5AD2-E Premium board? I've been trying for about an hour now to get the bad caps out, but I just can't get the solder to melt completely around the leads. I wicked out the top layer on the cool stack board itself, but it looks like there's another layer on the actual motherboard underneath. I have a 40 watt Weller iron with the base cranked all the way up. I was able to remove the other caps that aren't attached to this cool stack with no troubles at all.
Recapping Asus Board with Cool Stack
Collapse
X
-
Re: Recapping Asus Board with Cool Stack
Higher power iron and larger(wider) tip and use just the corner. Mine is a 3/16" wide, 800°F tip that does okay. None do well as these are through 2 circuit boards. Heat the other side of the board with a hair dryer to assist you, and leave it running while you work. Flux and add solder to each joint to increase the heat conduction.
The Cool Stack works well, no?
Which ones are you trying to remove?
VCore is Panasonic FL, and VRM is Ruby MBZ. They're fine.
The one ringer is an OST 1500uF that looks like a Ruby (same purple sleeve) on the corner of the CPU area towards the RAM. All the Ltec 820uF have to go.
ToastLast edited by Toasty; 11-02-2010, 09:57 PM.veritas odium parit -
Re: Recapping Asus Board with Cool Stack
Process for removing caps from multilayered PCBs:
1) Apply flux to the pins
2) Apply a little solder to each pin
3) Heat one pin andwith your hand underneath rock the cap back and forth while heating each side
Adding solder to the pin adds surface area for the heat to contact and melt the solder. Take your time and be patient, don't let the iron slip and damage the traces.
You don't need a high powered iron, any 25 watt junk iron can do this.Comment
-
Re: Recapping Asus Board with Cool Stack
Too low of watts and you are heating the whole PCB slowly vice just the joint quickly.
Beyond the fact it will take FOREVER to melt the solder you are highly likely to burn the pads right off the board.
.
Some people get by with a 40 watt but even that is too 'light' for most people.
For most people the sweet spot is the 50-60 watt range.
.Last edited by PCBONEZ; 12-03-2010, 12:23 PM.Mann-Made Global Warming.
- We should be more concerned about the Intellectual Climate.
-
Be who you are and say what you feel, because those who mind don't matter and those who matter don't mind.
- Dr Seuss
-
You can teach a man to fish and feed him for life, but if he can't handle sushi you must also teach him to cook.
-
Comment
-
Re: Recapping Asus Board with Cool Stack
FWIW: The correct name is Stack Cool.
Huh? What's a revoke station?
Fortunately the only caps that probably need replacement are those I mentioned in Post 2, the "ringer" OST and the Ltec's.
Toastveritas odium paritComment
-
Re: Recapping Asus Board with Cool Stack
NOT!
Too low of watts and you are heating the whole PCB slowly vice just the joint quickly.
Beyond the fact it will take FOREVER to melt the solder you are highly likely to burn the pads right off the board.
Some people get by with a 40 watt but even that is too 'light' for most people.
For most people the sweet spot is the 50-60 watt range.
.
I also recap Dell GX240s all the time with excellent results.
My iron is generic, and my electronics store miraculously carried the obscure thread-in bits which are out of production.Comment
-
Re: Recapping Asus Board with Cool Stack
Either you don't actually know the watts or your iron, you are an abomination, or you have made deals with the devil.
I suspect two of the three.
.Mann-Made Global Warming.
- We should be more concerned about the Intellectual Climate.
-
Be who you are and say what you feel, because those who mind don't matter and those who matter don't mind.
- Dr Seuss
-
You can teach a man to fish and feed him for life, but if he can't handle sushi you must also teach him to cook.
-
Comment
-
Re: Recapping Asus Board with Cool Stack
Are you using Chipquik or some other very low temperature solder? Because 25W is barely enough for desoldering single-layer boards, and I've had problems desoldering DIP chips from double-layer boards with less than 40W. I've found that the Radio Shack 45W desoldering iron, modified to minimize heat loss (insulate the top, cut the pipe to the sucker bulb), can do 4-layer boards.Comment
-
Re: Recapping Asus Board with Cool Stack
No, I'm not using chipquick. Your problem is your flux is weak. I use plumbing flux with my 25 or 35 watt irons and I have no problems. I can even desolder large coils from multi-layered boards. The 35-watt I found in the trash. If this hobby makes me a million dollars someday, I might consider investing in one of those overpriced irons, but until then, I refuse to pay.Comment
-
Re: Recapping Asus Board with Cool Stack
I don't care if you do use -ACID BASED FLUX-.
25 watts won't do it.
.Mann-Made Global Warming.
- We should be more concerned about the Intellectual Climate.
-
Be who you are and say what you feel, because those who mind don't matter and those who matter don't mind.
- Dr Seuss
-
You can teach a man to fish and feed him for life, but if he can't handle sushi you must also teach him to cook.
-
Comment
-
Re: Recapping Asus Board with Cool Stack
It has, and it does. In fact, I have four Dell GX240 boards I need to recap. I think I'll order a bunch of Samxon from Topcat for this one. Just yesterday I had to replace a GX240 board with blwon Nichicons, and the replacement I soldered is working fantastically.
If you want pictures, I'll be glad to oblige.Comment
-
Re: Recapping Asus Board with Cool Stack
Only if you get some good close-ups so I can point out the acid damage that will cause the eminent failure.Mann-Made Global Warming.
- We should be more concerned about the Intellectual Climate.
-
Be who you are and say what you feel, because those who mind don't matter and those who matter don't mind.
- Dr Seuss
-
You can teach a man to fish and feed him for life, but if he can't handle sushi you must also teach him to cook.
-
Comment
-
Re: Recapping Asus Board with Cool Stack
I don't use "massive amounts" - nowhere enough to cause damage to the PCB screen. Just a little dab on the joint - enough to encourage some melting - and I have stuff I recapped with this method working for years now. When I get the caps I'll do it.Comment
-
Re: Recapping Asus Board with Cool Stack
If you got your solder irons from trash cans then you have no idea if the previous owner stuck a 35w handle on a 40-50w iron or upgraded the element.
IOW: You don't know what watts your iron is.Mann-Made Global Warming.
- We should be more concerned about the Intellectual Climate.
-
Be who you are and say what you feel, because those who mind don't matter and those who matter don't mind.
- Dr Seuss
-
You can teach a man to fish and feed him for life, but if he can't handle sushi you must also teach him to cook.
-
Comment
-
Mann-Made Global Warming.
- We should be more concerned about the Intellectual Climate.
-
Be who you are and say what you feel, because those who mind don't matter and those who matter don't mind.
- Dr Seuss
-
You can teach a man to fish and feed him for life, but if he can't handle sushi you must also teach him to cook.
-
Comment
Related Topics
Collapse
-
Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?by Tynan DillI was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.
Upon bringing it home and plugging it up, it showed a standby light.
I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.
The screen seems to blackout and stay black, but with a flashlight I can see the display.
With my Playstation 4 connected via HDMI, and running a game I can hear sound.
Assuming...7 Photos -
by DynaxSCHi,
I have this very stubborn ASUS mobo on the bench, and I already face the wall with it. It just refuses to POST, although everything seems to be OK.
The situation looks like this:
After connecting the board to the power supply on Nuvoton (SLP_S3#, pin 64), the Low signal (50 ohm resistance) appears immediately. PWRNTN# signal goes through Nuvoton to the chipset (confirmed after removing the chipset). The following conditions are then met for the chipset to generate the SLP_S3# signal:
1. RTC oscillates normally (32.768KHz).
... -
by ShadowAi12Hi,
I recently bought an ASUS ROG STRIX B550-F GAMING motherboard that was listed as "dead, not powering on." However, it does show some signs of life. I've performed several basic measurements and would like to share the results.- The board enters a "ready to power on" state after plugging in the PSU.
- Pressing the power button increases power draw.
- Sometimes, touching the RSMRST_L pad with a multimeter probe causes the board to shut off and return to standby.
(taken after pressing the power button, while the board is attempting to start)- H_SKTOOC#
06-11-2025, 01:05 PM -
by jimbodriverHi everyone,
I am trying to learn electronics repair. I purchased a “faulty for spares/repairs” ASUS X99-PRO/ USB 3.1 motherboard for a very low price from ebay – a good enough price to offset the high probability that the board was completely toast and not realistically repairable.
Initial results:
Board would power-cycle when turned on either with switch on board or shorting pwr pins. Fan would spin for a second or so and a QCODE of 00 would display then it would power off and then do the same thing again over and over. I think maybe 2 times in about 100 attempts... -
by damndenisHello everybody,
This is my first post here, I've always loved to tinker with electronics, but never got in-depth with it. Hope I can learn a thing or two from this forum.
I've got a 31.5" Asus monitor which distorts/flickers at equal intervals of a couple of seconds. From what I've gathered, it's an issue with the T-CON board, but feel free to correct me. Shipping from the manufacturer would cost 3x as much as the part itself. I was wondering, if there is a way to diagnose the board itself and replace the faulty components? I'm good with soldering, but not at all...-
Channel: Troubleshooting Computer Displays
11-22-2024, 04:07 AM -
- Loading...
- No more items.
Comment