Bowers and Wilkins ZEPPELIN crappy caps

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • ReeceyBurger123
    Never Give Up !
    • May 2014
    • 7325
    • Britain

    #21
    Re: Bowers and Wilkins ZEPPELIN crappy caps

    Originally posted by jayjr1105
    I feel like modern Samxon GK's are pretty decent. I usually replace a lot of Samxon when I see them if I have a better replacement but usually they test very good esr when removed.
    I think it just depends on the cap it's self, I know it's obviously different defects with different batches. I've seen some crap craps that are known to fail last thousands of hours use way more than they should of in theory and still test fine. Newer Samxons aren't too bad either.
    Please Do Not PM My Page Asking For Help Badcaps Is The Place For Advise, Page Linked For Business Reasons Only. Anyone Doing So Will Be Banned Instantly !

    https://www.facebook.com/Telford-Tel...7894576335359/

    Comment

    Related Topics

    Collapse

    • sofles
      Bowers & Wilkins PX7 S2 Needed help with identifying charging IC
      by sofles
      Hi there,

      Recently I bought broken Bowers & Wilkins PX7 S2, the problem with them is that battery discharges on its own even with headphones turned off. It is a quite common issue with this model and even with model higher PX8.

      With help of thermal camera I found out that there is one IC that is hot even with headphones turned off. To check if I'm correct I bought another PX7 S2 working one and replaced small charging board with this IC and problem solved, battery no more drains on its own. After changing board back to original problem returned so I'm 100% sure problem...
      05-30-2025, 01:11 PM
    • eryjus
      Heathkit IO-4205 Power Supply Caps
      by eryjus
      Hello,

      First, I am a complete noob with high voltage stuff. I'm learning, but I need help by someone looking over my shoulder.

      I recently came into posession of a Heathkit IO-4205 5MHz Dual Trace Oscilloscope. The documentation is copyright 1978. I'm told it works.

      I opened it up to check the caps before I applied power, and found the following black caps and wanted to know what they were. They are on the power supply board. I was able to read the name and model and came up with, "Nytronics 162J-1, 0.1uF, 20% tolerance, 2000VDC."
      ...
      05-10-2023, 11:21 AM
    • Paxman_Swede
      Identifying caps on an old Zoom 9000
      by Paxman_Swede
      Hello!

      I have two projects on my work bench. One is a friends dead JBL Xtreme speaker with a blown voltage regulator and corresponding bulged and shorted cap. That cap has clear markings so I know what replacement I need for it.

      The other project however is a whole different deal. It's a Zoom 9000 guitar effect from the 90th that has developed a devil hound howl when there is no input from the guitar. I'm guessing caps problem. So, since I don't really use this effect anymore I thought it would be a perfect project to learn on.

      I have studied the board and...
      01-14-2025, 09:51 AM
    • captain150
      Help with switching power supply caps
      by captain150
      I'm trying to repair two old VCRs, they both have bad caps. One has leaky ones, the other would barely run until I subbed in some caps from another power supply I had laying around (though they are the wrong values). This vcr works for an hour or two, but then the power supply starts whining and the picture gets lines in it. I didn't replace all the secondary caps, so another voltage might still be problematic, or the values I used are too far off.
      I've been on mouser and digikey but the options are a bit overwhelming. I just need some new ones that will work. They don't need to be top quality,...
      03-16-2025, 07:34 PM
    • Foetuss
      Gigabyte GA-6OXT :: caps question
      by Foetuss
      Good evening

      I recently aquired a rev 1.1 Gigabyte 60XT, and was suprised of the amount of leaking caps for a motherboard of the P3 era. Especially the way the 330µf caps seems like the housing discolored even.
      Now, there are some 3300µF 6.3V KZG series around the CPU. Would it be OK to replace them with something like EEUFR1A332 ? (Panasonic FR 3300µF 10V). Or was this board designed around very low ESR caps?

      But I was also suprised about the bigger boys, which are 330µF 25V.
      Could it be they used 25V caps because they were cheaper / available at that time?...
      02-11-2025, 12:22 PM
    • Loading...
    • No more items.
    Working...