Try our *UPDATED* boardview, bios, & schematic search. Over 2.3 million files for download!

Creative Gigaworks S750

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • alukino
    New Member
    • May 2026
    • 4
    • italy

    #101
    Originally posted by Agent24
    It could be a capacitor issue, but you can get heat-sensitive faults with almost any component.

    You could replace all the capacitors but this may not fix it. If the problem remained, you'd have to start searching for the offending component with freezer spray and hot air, etc.

    Sometimes you can get lucky and careful visual inspection will find a dubious looking component, which turns out to be faulty.

    Another possible issue of course is bad solder joints. Inspect and reflow any that look suspicious. That by itself may fix the problem.

    I don't understand even if I have already soldered / tinned it and it's not difficult but it doesn't make you put the same components but of superior quality
    Kind of differences
    UHW1V221MPD
    EEUEB1V221B
    The one below is better, it has a much lower impedance and a higher working current [which is better on paper] but here the problem is like 4 5 6 times higher. 1.6A
    I wanted an opinion on the small 100nf 50v and the fairly poor audio filter from what I understand around, I can put a 100nf 63v or 100nf 100v in polypropylene which is much much better.
    I wanted to confirm this, other thing, can I put the 400v on 450v?
    Attached Files

    Premium supporters get full download access and other benefits.

    Comment

    • alukino
      New Member
      • May 2026
      • 4
      • italy

      #102
      Originally posted by Agent24
      It could be a capacitor issue, but you can get heat-sensitive faults with almost any component.

      You could replace all the capacitors but this may not fix it. If the problem remained, you'd have to start searching for the offending component with freezer spray and hot air, etc.

      Sometimes you can get lucky and careful visual inspection will find a dubious looking component, which turns out to be faulty.

      Another possible issue of course is bad solder joints. Inspect and reflow any that look suspicious. That by itself may fix the problem.
      I don't understand even if I have already soldered / tinned it and it's not difficult but it doesn't make you put the same components but of superior quality
      Kind of differences
      UHW1V221MPD
      EEUEB1V221B
      The one below is better, it has a much lower impedance and a higher working current [which is better on paper] but here the problem is like 4 5 6 times higher. 1.6A
      I wanted an opinion on the small 100nf 50v and the fairly poor audio filter from what I understand around, I can put a 100nf 63v or 100nf 100v in polypropylene which is much much better.
      I wanted to confirm this, other thing, can I put the 400v on 450v?
      Attached Files

      Premium supporters get full download access and other benefits.

      Comment

      • Agent24
        I see dead caps
        • Oct 2007
        • 5401
        • New Zealand
        • Electronics and computer repair

        #103
        I'm saying the unit could have bad solder joints from the factory, and that might be why you've having thermal-related issues. Cold or cracked solder joints can sometimes cause temperature dependent problems. It's not always just capacitors.

        Check voltage rails when it's cold and see if you get low voltage or high ripple etc. That will tell you if it's likely capacitors or not.

        The two different 220uF 35v capacitors you listed have very different ripple current ratings, 1600mA vs 197mA
        The Panasonic one also doesn't even list an ESR value. Is the Nichicon the original, or the Panasonic?

        You can probably change an electrolytic for a film capacitor in the audio path, but I doubt it will sound any different.

        I would NOT replace the 450v capacitor with a 400v one. This unit probably uses APFC and runs at a boosted voltage close to 400v. That's why they're using the 450v capacitor.

        I also see a lot of crappy cheap glue all over this thing. That glue likes to go conductive and corrosive over time as it absorbs moisture...
        "Tantalum for the brave, Solid Aluminium for the wise, Wet Electrolytic for the adventurous"
        -David VanHorn

        Comment

        • alukino
          New Member
          • May 2026
          • 4
          • italy

          #104
          I did it, I changed the capacitors and now it works perfectly

          Comment

          • fr3d3r3r
            New Member
            • Nov 2021
            • 4
            • France

            #105
            Hello. I'm trying to identify capacitor C40 to replace it. But I can't find the reference. If you have it, that would be great. I' ve attached a photo of my exploded C40s if it can help. Thank you.
            Attached Files

            Premium supporters get full download access and other benefits.

            Comment

            • madan1
              Badcaps Veteran
              • Nov 2016
              • 775
              • Bulgaria

              #106
              Originally posted by fr3d3r3r
              Hello. I'm trying to identify capacitor C40 to replace it. But I can't find the reference. If you have it, that would be great. I' ve attached a photo of my exploded C40s if it can help. Thank you.
              Did you check posts #43 and #46?

              Comment

              • fr3d3r3r
                New Member
                • Nov 2021
                • 4
                • France

                #107
                Originally posted by madan1

                Did you check posts #43 and #46?
                Thank you very much, I just looked. So I ordered a 1uF 250V non-polarized polyester capacitor. As soon as I receive it, I'll let you know how the repair goes.
                Attached Files

                Premium supporters get full download access and other benefits.

                Comment

                • Agent24
                  I see dead caps
                  • Oct 2007
                  • 5401
                  • New Zealand
                  • Electronics and computer repair

                  #108
                  You should replace the electrolytics too, they look very damaged from the heat.
                  "Tantalum for the brave, Solid Aluminium for the wise, Wet Electrolytic for the adventurous"
                  -David VanHorn

                  Comment

                  • fr3d3r3r
                    New Member
                    • Nov 2021
                    • 4
                    • France

                    #109
                    Hello guys. I've replaced all electrolytics as you said. ,But I detected a fault on the capacitor c39. I would need to connect it directly to the relevant component; do you know which one it is? Thank you very much.

                    Comment

                    • Agent24
                      I see dead caps
                      • Oct 2007
                      • 5401
                      • New Zealand
                      • Electronics and computer repair

                      #110
                      Originally posted by fr3d3r3r
                      Hello guys. I've replaced all electrolytics as you said. ,But I detected a fault on the capacitor c39. I would need to connect it directly to the relevant component; do you know which one it is? Thank you very much.
                      Sorry, I'm not sure what you mean. What exactly is wrong with C39?
                      "Tantalum for the brave, Solid Aluminium for the wise, Wet Electrolytic for the adventurous"
                      -David VanHorn

                      Comment

                      • fr3d3r3r
                        New Member
                        • Nov 2021
                        • 4
                        • France

                        #111
                        Hi everyone. It worked! C40 is indeed a 1µF 100V capacitor. I took the opportunity to scrape off the glue (Replaced with neutral silicone RTV)
                        and replace all the capacitors. There was also an electrical arc on T0-220, because of a damaged screw seal. I also replaced the plates between the T0-220 and the heatsink, and changed the thermal paste. Thanks everyone for your replies.

                        Comment

                        Related Topics

                        Collapse

                        • Andreasbest
                          HP LA-H32AP motherboard power on for 5 secs
                          by Andreasbest
                          Hello.
                          Received a LA-H32AP motherboard with AMD cpu, only reaction is the power led (LED1) that lights up for 5 secs, nothing else.
                          Summary↓

                          The laptop was working normally the previous day.

                          When pressing the power button, LED1 (Power LED) turns on for a few seconds and then turns off. The motherboard does not boot.

                          Some power rails remain active for several seconds after LED1 turns off.

                          Troubleshooting already performed:
                          • Tested different RAM modules.
                          • Tested without RAM.
                          • Tested again with RAM installed — exactly the same behavior.
                          • Removed
                          ...
                          10-19-2026, 03:11 PM
                        • calebtree33
                          Nitro 5 AN515-58 Power Up Sequence Failure
                          by calebtree33
                          Device: Acer Nitro 5 AN515-58-5046
                          Board: LA-L973P HH514

                          Context: I bought this from a guy hoping to fix it and resell it as I am learning motherboard repair. He said that the laptop would start powering up, fans would spin, and keyboard backlight would turn on. When the screen turned on, the time was wrong. Eventually it stopped turning on altogether. I am confused as to how this could be a gradual failure.

                          Problem: When pressing the power button the LED showed for about 5 seconds before shutting off. The laptop would charge with the charging light. I cannot find...
                          09-24-2026, 08:18 PM
                        • Tynan Dill
                          Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
                          by Tynan Dill
                          I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

                          Upon bringing it home and plugging it up, it showed a standby light.

                          I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

                          The screen seems to blackout and stay black, but with a flashlight I can see the display.

                          With my Playstation 4 connected via HDMI, and running a game I can hear sound.

                          Assuming...
                          11-22-2024, 01:46 PM
                        • PantherDave
                          Microsoft Surface Pro (5th gen) model 1796 - no power
                          by PantherDave
                          Hi all!

                          I'm trying to troubleshoot a Microsoft Surface Pro (5th gen) model 1796 that won't power on. Motherboard model is M1007506-015. My priority is retrieving data, but the SSD is integrated so it looks like if I can't repair it it'll need to go to a data recovery company. I've done a little basic board repair before, but nothing this advanced until now. So please forgive my ignorance in advance. 😅

                          I found the boardview for this laptop in the forums here, and am able to open it on my PC with FlexBV.
                          https://www.badcaps.net/forum/troubl...-hardware-devi...
                          05-29-2024, 02:01 PM
                        • GLISIT
                          Asus Probook P5440UF-XB74 power issue
                          by GLISIT
                          Hi all,

                          TL;DR - this laptop is driving me nuts with the oddball power-related behaviors. Appreciate any insight you can provide!


                          I'm experiencing a power issue on an Asus Probook P5440UF-XB74. Although I've worked with electronics and computers for decades, this is my first attempt at getting into motherboard-level component troubleshooting. Any help the community can provide is greatly appreciated!

                          A few weeks ago I was using the laptop (on battery power) for a Zoom meeting. The battery was running very low (long meeting) but I wasn't worried about...
                          01-16-2025, 02:29 PM
                        • Loading...
                        • No more items.
                        Working...