New Software Achi LY by PSOFT

[Hampy]

Re: New Software Achi LY by PSOFT

I do not know if there is software that can help you, if you have the time and know a programming language like the C on the altec site in the download section there is a document about AL808 that has the same communication protocol.
AL808 communication protocol
http://www.altec.cc/english/downloads.htm

AL808 communication test software
http://www.altec.cc/DownloadFile/AL808TEST.rar

Hello,
I already have the manual and the software. But the software is only available in Chinese. That's my problem. And without software, I can not control my kiln

[jasko_jacker]

Re: New Software Achi LY by PSOFT

like this ?

http://www.instructables.com/id/Home...s-fusing-kiln/

[JLCurve]

Re: New Software Achi LY by PSOFT

Funny, I just did a small c program yesterday to access the Altec PC410 with *nix os. I will publish it in the coming days on Github. Had one in my BGA rework station but bought another for a ceramic kiln.

It's a basic application to communicate with the controller so you will need to wrap it in a scrip or other if you want a full control software. My goal was to be able to record/plot the heating curves and view them in HTML..

Will post the github project when on-line.

Cheers!
J.

[JLCurve]

Re: New Software Achi LY by PSOFT

Still needs a LOT of polishing but, here's the repository :
https://github.com/curve514/sendaltec

[laoveja]

Usually in many bga rework machine (chinese brand) the top heater is
drived by altec p410 and bottom heater by rex-c100 (on the internet many altec or rex are clones) but
while the upper heater is operated by the altec that follows the set profiles, the temperature of the lower heater gradually changes from min to max, regardless of the temperature on the motherboard.
Instead, this software drive the bottom heater to generate a temperature on the bottom layer of motherboard proportionally to a temperature on top layer.
The circuits of the controllers are separated, each one has a digital relay and an input for the thermocouple, but only the altec has a rs232 port and therefore a software can only drive the top heater.
With an easy modification you can solve this problem and use the psoft program. To avoid errors in temperature it is important that the two temocouples are positioned on the same point, or very close; one on top and the other on the bottom layer

Hi! I want to know which modifications are needed. I have an achi ir pro sc v3

[STR13]

Re: New Software Achi LY by PSOFT

Hello all. first time poster. I downloaded the Psoft software. I am on windows 10 and can't seem to figure out where to put the language file so the application will translate to English. Any help would be appreciated, thanks.

[jasko_jacker]

Re: New Software Achi LY by PSOFT

Hello all. first time poster. I downloaded the Psoft software. I am on windows 10 and can't seem to figure out where to put the language file so the application will translate to English. Any help would be appreciated, thanks.

see the pic

[jasko_jacker]

Re: New Software Achi LY by PSOFT

Hi! I want to know which modifications are needed. I have an achi ir pro sc v3

See the pic, on pin 9 and 10 ( not remove the thermocouple cables), connect these outputs to pins 16-17 of the altec

from rex disconect negative on ssr out (pin 5) and connect to pin 7 (out 2) on altec, connect pin 6 from altec (out 2) to negative pin on ssr

[STR13]

Re: New Software Achi LY by PSOFT

see the pic

Thank you so much for your fast reply!

I seem to have run into another issue. When I try and open a COM port to my ACHI IR6500 via a USB to USB cable to a windows 10 laptop, I get an error message that say "port COM1 does not exist" When I plug the IR6500 into the laptop it does seem recognize it. If I could get some help on resolving this issue I'd greatly appreciate it. This is my first rework station and I'm just trying to get it up and running. Thanks for your time.

[jasko_jacker]

Re: New Software Achi LY by PSOFT

Have you inserti the correct parameter i(com1, baud rate. Etc) ? If you use a com adapter fine it in device manager -> preperty ...... and change the parameters

[STR13]

Re: New Software Achi LY by PSOFT

I was able to get the software to work with my Achi IR6500. I don't know if this is the correct post for this thread and do apologize if it isn't, I've run into another slight problem. The Altec PC410 controller displays probe temperature as a negative integer. Meaning it starts out at 20/21 C (room temperature) and as the temperature gets hotter, the displayed value decreases, eventually reading a negative number (-20). I've been googling trying to find a solution. If anyone here knows anything or can point me in the correct direction I'd greatly appreciate it. Thanks for your time.

[jasko_jacker]

Re: New Software Achi LY by PSOFT

Check if thermocouple cable are insert correctly (+ +, - -)

[jacobfernando]

Re: New Software Achi LY by PSOFT

Hi sorry to ask with the modification will psoft control the bottom heater aswell? And also the power heating power for both heaters?.
Thanks

[RavoLx]

Re: New Software Achi LY by PSOFT

i have the same problem whit the software i have ir6500

[jasko_jacker]

Re: New Software Achi LY by PSOFT

Hi sorry to ask with the modification will psoft control the bottom heater aswell? And also the power heating power for both heaters?.
Thanks

Psoft can control bottom heather Only if you set auto+x
otherwise the bottom temp is controlled by Rex controller and you can only set the percentage of bottom power respect the temperature reached in a certain moment.
You can start setting auto+x = 10

[jasko_jacker]

Re: New Software Achi LY by PSOFT

i have the same problem whit the software i have ir6500

if your soldering machine works with the original software, there is no reason why it does not work with psoft, check the connections and the settings of the com port in device manager.

[RavoLx]

Re: New Software Achi LY by PSOFT

yeah all setting is ok ACHI IR SOFT work fine but the PSoft Rework keep give me COM CLOSE

any idea

[RavoLx]

Re: New Software Achi LY by PSOFT

i have change the data bit to 7 and it work, just a quick question it normal that the Com Open keep flashing

[jasko_jacker]

Re: New Software Achi LY by PSOFT

i have change the data bit to 7 and it work, just a quick question it normal that the Com Open keep flashing

Yes it's correct,
to avoid motherboard damage, place bottom thermocouple and top thermocouple not at opposite side respect bga chip.
Set Rex at 190-195 C° if you see that the bottom temp is to hight
change (auto+x = 5) and check rex settings.
Test thermocople with ice (fused ice) to check 0° C and with a sn/pb alloy to check 180° C

[jacobfernando]

Psoft can control bottom heather Only if you set auto+x
otherwise the bottom temp is controlled by Rex controller and you can only set the percentage of bottom power respect the temperature reached in a certain moment.
You can start setting auto+x = 10

Thanks for the reply so if modify the connections as you explain before it will control all the temps and curve