Announcement

Collapse
No announcement yet.

ESR meter upgrades

Collapse
This is a sticky topic.
X
X
 
  • Filter
  • Time
  • Show
Clear All
new posts
  • vinceroger69
    Badcaps Legend
    • Mar 2012
    • 6571
    • uk

    Re: ESR meter upgrades

    Originally posted by stj View Post
    16v was a minimum figure,

    104 = 100nf
    103 = 10nf
    cheers stj it wasnt really the voltage i was worried as you said 10 uf these are 100uf will that be ok?

    Comment

    • stj
      stj
      Great Sage 齊天大聖
      • Dec 2009
      • 29527
      • some shithole run by Israeli agents

      Re: ESR meter upgrades

      fine, they are only power-smoothing

      Comment

      • vinceroger69
        Badcaps Legend
        • Mar 2012
        • 6571
        • uk

        Re: ESR meter upgrades

        cheers stj i will have ago tomorrow at building this kit and post the results.

        Comment

        • stj
          stj
          Great Sage 齊天大聖
          • Dec 2009
          • 29527
          • some shithole run by Israeli agents

          Re: ESR meter upgrades

          upgrades
          http://uk.rs-online.com/web/p/crystal-units/8149440/

          http://uk.rs-online.com/web/p/voltag...ences/5343037/

          http://uk.rs-online.com/web/p/idc-connectors/6257252/

          and:
          http://www.ebay.co.uk/itm/272041588746
          Last edited by stj; 06-19-2016, 05:27 PM.

          Comment

          • vinceroger69
            Badcaps Legend
            • Mar 2012
            • 6571
            • uk

            Re: ESR meter upgrades

            next time i place a rs order i will add those too it stj what will i need too do regarding software upgrades ive got to admit ive never dealt with this side of things ie re programing chips etc so i guess i will need a chip re programmer?

            Comment

            • stj
              stj
              Great Sage 齊天大聖
              • Dec 2009
              • 29527
              • some shithole run by Israeli agents

              Re: ESR meter upgrades

              updated the previous post.
              Last edited by stj; 06-19-2016, 05:28 PM.

              Comment

              • vinceroger69
                Badcaps Legend
                • Mar 2012
                • 6571
                • uk

                Re: ESR meter upgrades

                Originally posted by stj View Post
                updated the previous post.
                Thanks again i will get the kit built up and tested etc then will order the upgrades and go from there.

                Comment

                • stj
                  stj
                  Great Sage 齊天大聖
                  • Dec 2009
                  • 29527
                  • some shithole run by Israeli agents

                  Re: ESR meter upgrades

                  btw, you need a decent cap to calibrate it.
                  100n - 1uf preferably film type.
                  i use a 220nf polyester cap.
                  you can salvage one from some junk.

                  Comment

                  • vinceroger69
                    Badcaps Legend
                    • Mar 2012
                    • 6571
                    • uk

                    Re: ESR meter upgrades

                    cheers stj i have already got a pack of 100nf polyester caps here so willl use one of these if its ok just to clarify something each time you remove the 9volt battery do you have too re calabrate these units? (i always do but wasnt sure if needed too)

                    Comment

                    • vinceroger69
                      Badcaps Legend
                      • Mar 2012
                      • 6571
                      • uk

                      Re: ESR meter upgrades

                      update for stj ive built the kit up as per your list bad news does not power up on pin 7 and 22 of the empty ic socket i get about 1.46v should be 5v i think? the screen does flash very quickly with the ic installed, now i dont want to start swopping resistors around etc as its really hard to remove them and leave a clear hole in the pcb the good news is the ebay seller of the kit has refunded me fully so ive just ordered a pre built kit from a diffrent store but exactly the same board revision etc so when it comes i will check all resistor values as per good working tester and the one ive built as a kit and see where ive gone wrong i did double check all the resistor values today using the hobby-hour calculator and all seems spot on with your list so will update this thread as soon as the pre built kit arrives.
                      Last edited by vinceroger69; 06-20-2016, 07:26 AM.

                      Comment

                      • stj
                        stj
                        Great Sage 齊天大聖
                        • Dec 2009
                        • 29527
                        • some shithole run by Israeli agents

                        Re: ESR meter upgrades

                        Originally posted by vinceroger69 View Post
                        cheers stj i have already got a pack of 100nf polyester caps here so willl use one of these if its ok just to clarify something each time you remove the 9volt battery do you have too re calabrate these units? (i always do but wasnt sure if needed too)
                        it's saved in the eeprom.

                        Comment

                        • stj
                          stj
                          Great Sage 齊天大聖
                          • Dec 2009
                          • 29527
                          • some shithole run by Israeli agents

                          Re: ESR meter upgrades

                          Originally posted by vinceroger69 View Post
                          update for stj ive built the kit up as per your list bad news does not power up on pin 7 and 22 of the empty ic socket i get about 1.46v should be 5v i think? the screen does flash very quickly with the ic installed, now i dont want to start swopping resistors around etc as its really hard to remove them and leave a clear hole in the pcb the good news is the ebay seller of the kit has refunded me fully so ive just ordered a pre built kit from a diffrent store but exactly the same board revision etc so when it comes i will check all resistor values as per good working tester and the one ive built as a kit and see where ive gone wrong i did double check all the resistor values today using the hobby-hour calculator and all seems spot on with your list so will update this thread as soon as the pre built kit arrives.
                          short the emitter and collector on the 4673 transistor and try again - not sure what the hell a 4673 is anyway!

                          Comment

                          • vinceroger69
                            Badcaps Legend
                            • Mar 2012
                            • 6571
                            • uk

                            Re: ESR meter upgrades

                            im not sure what it is either no data sheet that i can see and the numbers rite as just checked wasnt sure wich pins to link but tried all combinatons no change hopefully pre built tester will be here soon last kit only took 9 days to arrive.
                            ive emailed all the sellers selling this version of the kit none come with part location/values etc, instructions and none will send me a picture so we can see resistor colour bands clearly i think thats why i got a refund so fast too as maybe other people buying these kits are having trouble too.
                            Last edited by vinceroger69; 06-20-2016, 08:44 AM.

                            Comment

                            • stj
                              stj
                              Great Sage 齊天大聖
                              • Dec 2009
                              • 29527
                              • some shithole run by Israeli agents

                              Re: ESR meter upgrades

                              short the center pin to the pin nearest the battery + lead.

                              then you should see 9v on the rightmost pin of the surface-mount 1117 regulator, and 5v coming out of the tab.

                              if you dont, check the electrolytics arent reversed and check between those points and ground for a short.
                              because frankly - there is nothing else involved in generating the 5v.

                              Comment

                              • vinceroger69
                                Badcaps Legend
                                • Mar 2012
                                • 6571
                                • uk

                                Re: ESR meter upgrades

                                bear with me stj im going over each part ive fitted just too double check my parts ive fitted are in the correct locations etc and just nipping to get my multi meter back as was using a cheap one (neighbours borrowing my good one)

                                Comment

                                • vinceroger69
                                  Badcaps Legend
                                  • Mar 2012
                                  • 6571
                                  • uk

                                  Re: ESR meter upgrades

                                  So a update with my good meter and new battery pins 7 and 22 5.01 v when hold rotary switch down bad news screen will only stay lit with no writing on screen just backlight? when rotary switch is held down no led on board lit when testing voltage or when switch held down.

                                  Comment

                                  • stj
                                    stj
                                    Great Sage 齊天大聖
                                    • Dec 2009
                                    • 29527
                                    • some shithole run by Israeli agents

                                    Re: ESR meter upgrades

                                    i dont understand what you said!

                                    what happens if you press the encoder for a second?

                                    btw, the led wont light when the button is held down because of how it's wired.
                                    Last edited by stj; 06-20-2016, 09:26 AM.

                                    Comment

                                    • vinceroger69
                                      Badcaps Legend
                                      • Mar 2012
                                      • 6571
                                      • uk

                                      Re: ESR meter upgrades

                                      when encoder held down have 5v on the socket pins ok re install ic press encoder button backlight very quick flash then off.

                                      Comment

                                      • stj
                                        stj
                                        Great Sage 齊天大聖
                                        • Dec 2009
                                        • 29527
                                        • some shithole run by Israeli agents

                                        Re: ESR meter upgrades

                                        could be cpu not running.
                                        does your meter have a frequency counter?

                                        Comment

                                        • vinceroger69
                                          Badcaps Legend
                                          • Mar 2012
                                          • 6571
                                          • uk

                                          Re: ESR meter upgrades

                                          ita a maplin meter PG017 it does say hz lo/hi

                                          Comment

                                          Working...
                                          X