Badcaps.net Forum
Go Back   Badcaps Forums > Electronics Theory and Troubleshooting > Troubleshooting TVs and Video Sources
Register FAQ Calendar Search Today's Posts Mark Forums Read

 
Thread Tools Display Modes
Old 05-19-2017, 11:07 PM   #61
budm
Badcaps Veteran
 
budm's Avatar
 
Join Date: Feb 2010
City & State: S.F. Bay area
My Country: USA
Line Voltage: 120V 60Hz
I'm a: Knowledge Seeker
Posts: 30,494
Default Re: LG 42LG50FD-AD Intermittent NoGo

Pin 9 PWMCNTL is an open Drain, that MOSFET is normally low (on) but goes high if the Output is higher than the set limit and that is sensed by pin 8 HVSEN which it works in conjunction with VSENSE..
I would check Voltage at pin 7 VINAC since those high Ohm resistors in that sensing network tend to drift in values.
Look at page 10 for 'TYPICAL CHARACTERISTICS'
I did not read the whole spec sheet yet.
Attached Files
File Type: pdf ucc28060.pdf (1.18 MB, 3 views)
__________________
Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956

Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999

Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl

Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/

TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809
budm is offline   Reply With Quote
Old 05-20-2017, 04:00 AM   #62
Amraks
Badcaps Veteran
 
Join Date: Nov 2011
City & State: Tasmania, Northwest
My Country: Australia
Line Voltage: 240VAC
I'm a: Knowledge Seeker
Posts: 498
Default Re: LG 42LG50FD-AD Intermittent NoGo

Pin 7(VINAC) = 4.131v
this is 1 volt over characteristics
Amraks is offline   Reply With Quote
Old 05-20-2017, 10:25 AM   #63
Amraks
Badcaps Veteran
 
Join Date: Nov 2011
City & State: Tasmania, Northwest
My Country: Australia
Line Voltage: 240VAC
I'm a: Knowledge Seeker
Posts: 498
Default Re: LG 42LG50FD-AD Intermittent NoGo

Just noticed pin 7 is connected to pin 8. so basically I have just checked voltages on both lines.

VINAC and HVSEN
Amraks is offline   Reply With Quote
Old 05-20-2017, 12:19 PM   #64
Amraks
Badcaps Veteran
 
Join Date: Nov 2011
City & State: Tasmania, Northwest
My Country: Australia
Line Voltage: 240VAC
I'm a: Knowledge Seeker
Posts: 498
Default Re: LG 42LG50FD-AD Intermittent NoGo

Found some resistors that look low. 7503(7.5m) they test 1000k lower about 6.5m these lead to pin 1 ucc2806.
Also on that pin 7 circuit of the resistor 5101(5.5k) is showing really low about 3.692k.
Attached Images
File Type: jpg resistor network.jpg (2.04 MB, 7 views)

Last edited by Amraks; 05-20-2017 at 12:44 PM..
Amraks is offline   Reply With Quote
Old 05-20-2017, 10:22 PM   #65
Amraks
Badcaps Veteran
 
Join Date: Nov 2011
City & State: Tasmania, Northwest
My Country: Australia
Line Voltage: 240VAC
I'm a: Knowledge Seeker
Posts: 498
Default Re: LG 42LG50FD-AD Intermittent NoGo

Probed the VCDA and VCDB 500 - 560 mv my understanding this is meant to be zero only 2 mv

Last edited by Amraks; 05-20-2017 at 10:29 PM..
Amraks is offline   Reply With Quote
Old 05-20-2017, 10:50 PM   #66
Amraks
Badcaps Veteran
 
Join Date: Nov 2011
City & State: Tasmania, Northwest
My Country: Australia
Line Voltage: 240VAC
I'm a: Knowledge Seeker
Posts: 498
Default Re: LG 42LG50FD-AD Intermittent NoGo

VSENSE Voltage = 6.59v
Found some more resistors in that network that are 7503's they are all over the place in measurements
Amraks is offline   Reply With Quote
Old 05-21-2017, 01:57 AM   #67
Amraks
Badcaps Veteran
 
Join Date: Nov 2011
City & State: Tasmania, Northwest
My Country: Australia
Line Voltage: 240VAC
I'm a: Knowledge Seeker
Posts: 498
Default Re: LG 42LG50FD-AD Intermittent NoGo

My bad the 7503s are 750kohms the calculator i was using wasn't very good. rechecked them with a phone app.
They are all over the shop will I have to pull these out of circuit to test as I don't see them in parallel with anything.

http://www.ebay.com.au/itm/200pcs-RK...YAAOSwLnBX5MJI

Last edited by Amraks; 05-21-2017 at 01:59 AM..
Amraks is offline   Reply With Quote
Old 05-28-2017, 08:36 PM   #68
Amraks
Badcaps Veteran
 
Join Date: Nov 2011
City & State: Tasmania, Northwest
My Country: Australia
Line Voltage: 240VAC
I'm a: Knowledge Seeker
Posts: 498
Default Re: LG 42LG50FD-AD Intermittent NoGo

The 8x 7503 resistors have been replaced now the TV works thanks budm for the help you was right about them resistors.

end up replacing the 7503 resistors with Bourns CHV0805-FX-7503ELF

Last edited by Amraks; 05-28-2017 at 08:39 PM..
Amraks is offline   Reply With Quote
Old 05-28-2017, 11:12 PM   #69
budm
Badcaps Veteran
 
budm's Avatar
 
Join Date: Feb 2010
City & State: S.F. Bay area
My Country: USA
Line Voltage: 120V 60Hz
I'm a: Knowledge Seeker
Posts: 30,494
Default Re: LG 42LG50FD-AD Intermittent NoGo

Glad to hear you got it fix, have to watch out for those resistor in the high Voltage section, they tend to drift off the values and cause problem in sensing circuits.
budm is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



Badcaps.net Technical Forums 2003 - 2017
Powered by vBulletin ®
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
All times are GMT -6. The time now is 11:04 AM.

Did you find this forum helpful?