Badcaps.net Forum
Go Back   Badcaps Forums > Troubleshooting Hardware & Devices and Electronics Theory > Troubleshooting Audio Equipment
Register FAQ Calendar Search Today's Posts Mark Forums Read

 
Thread Tools Display Modes
Old 02-23-2021, 04:29 PM   #1
ricco75
New Member
 
Join Date: Feb 2021
City & State: PARIS
My Country: FRANCE
I'm a: Knowledge Seeker
Posts: 2
Default ONKYO TX-SR607 ; FL Tube LCD Replacement ?

Hello
I have bought few years ago a ONKYO TX-SR607.
No problem with it since one month..
Everything working well except LCD... i have a black screen.
I have found this post :

https://www.justanswer.com/electroni...splay-not.html

this schematic information

https://www.commentreparer.com/doc/15372/onkyo.pdf

I have check the resistance R950 and no problem with it i have replace it by a new one : same
I have control on Q7002 tension and i have 4.1V

I think electric my problem is FL tube inside.




Is someone have try to change it ?
It is possible ?

Thanks

Last edited by ricco75; 02-23-2021 at 04:57 PM..
ricco75 is offline   Reply With Quote
Old 02-26-2021, 12:35 AM   #2
redwire
Badcaps Veteran
 
Join Date: Dec 2010
City & State: Alberta
My Country: Canada
Posts: 1,993
Default Re: ONKYO TX-SR607 ; FL Tube LCD Replacement ?

It is common to have bad solder joints at the tube because the pins are made of Kovar and do not solder easily. Or the power transformer pins have bad solder connections, or at the middle board.

For a dead fluorescent display, check that the tube has power to the filament. You can also see the lines glow orange in a dark room. I guess it should be about 6VAC between pin 1, 62 on the tube FLAC1, FLAC2 from the AMP PWB with R950 then P950, P951 on big transformer T901. It should go to the power transformer winding S2. I had one amp with a bad solder joint at the transformer's pins (varnish). You have to trace it back, or measure ohms for each lead from display to transformer. - BUT the low winding and filament resistance can fool you into thinking the connection is good.

If the tube has air in it, the getter will turn white.

Last edited by redwire; 02-26-2021 at 12:37 AM..
redwire is offline   Reply With Quote
Old 02-26-2021, 11:12 PM   #3
redwire
Badcaps Veteran
 
Join Date: Dec 2010
City & State: Alberta
My Country: Canada
Posts: 1,993
Default Re: ONKYO TX-SR607 ; FL Tube LCD Replacement ?

Another note, the Onkyo has three step brightness control (DIMMER button) on the remote and see what that does.
redwire is offline   Reply With Quote
Old 02-27-2021, 07:32 AM   #4
stj
Great Sage 齊天大聖
 
stj's Avatar
 
Join Date: Dec 2009
City & State: Europe
My Country: some shithole run by Israeli agents
I'm a: Professional Tech
Posts: 24,373
Default Re: ONKYO TX-SR607 ; FL Tube LCD Replacement ?

look for electrolytic caps connected with it.
if you find one, try using a 1uf polyester in it's place.
stj is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



Badcaps.net Technical Forums 2003 - 2021
Powered by vBulletin ®
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
All times are GMT -6. The time now is 02:01 AM.
Did you find this forum helpful?