Badcaps.net Forum
Go Back   Badcaps Forums > Troubleshooting Hardware & Devices and Electronics Theory > Troubleshooting Computer Displays
Register FAQ Calendar Search Today's Posts Mark Forums Read

 
Thread Tools Display Modes
Old 06-07-2019, 06:42 AM   #41
stj
Great Sage 齊天大聖
 
stj's Avatar
 
Join Date: Dec 2009
City & State: Europe
My Country: some shithole run by Israeli agents
I'm a: Professional Tech
Posts: 20,761
Default Re: Help with dead Commodore 1802

i have never seen as resistor fail without help.
a 40w lamp bulb in series with the monitor is a good idea to limit the current.
and leave the degausing coil unplugged - it's the thing that causes the bong sound - and causes a big surge.
it's around the outer edge of the front of the tube, and runs to a 2pin connector near the mains input.
stj is offline   Reply With Quote
Old 06-07-2019, 02:31 PM   #42
roadrash
Badcaps Veteran
 
roadrash's Avatar
 
Join Date: Oct 2015
City & State: Cambridgeshire
My Country: U.K.
Line Voltage: 240VAC
I'm a: Knowledge Seeker
Posts: 274
Default Re: Help with dead Commodore 1802

Quote:
Originally Posted by R_J View Post
It blew the 3.3Ω 10 watt resistor! but not the fuse? Ok check the 4 power supply diodes, then check the resistance across the main capacitor. You must have a dead short somewhere in the primary circuit
Post a picture of that new resistor that blew open
R505 shows as a dead short. Would this be the culprit?
All others like 4 diodes are ok
roadrash is offline   Reply With Quote
Old 06-07-2019, 03:45 PM   #43
stj
Great Sage 齊天大聖
 
stj's Avatar
 
Join Date: Dec 2009
City & State: Europe
My Country: some shithole run by Israeli agents
I'm a: Professional Tech
Posts: 20,761
Default Re: Help with dead Commodore 1802

no, it's supposed to be 0.27ohms

desolder coil L805, connect a 40w mains bulb to the pins of C812 and try it again.
then your only running the psu and the audio amp - not the rest of the circuit.
you need the light because the psu expects a load.
stj is offline   Reply With Quote
Old 06-07-2019, 06:13 PM   #44
R_J
Badcaps Veteran
 
Join Date: Jun 2012
City & State: ☻
My Country: Canada
I'm a: Professional Tech
Posts: 4,133
Default Re: Help with dead Commodore 1802

So no short across the main capacitor?, You can also check the output transistor in the str54041 (E=pin4,C=pin3,B=pin2) however I suspect that if the str was bad it should have blown R805 (0.27Ω)
R_J is offline   Reply With Quote
Old 06-08-2019, 03:33 AM   #45
roadrash
Badcaps Veteran
 
roadrash's Avatar
 
Join Date: Oct 2015
City & State: Cambridgeshire
My Country: U.K.
Line Voltage: 240VAC
I'm a: Knowledge Seeker
Posts: 274
Default Re: Help with dead Commodore 1802

8
Quote:
Originally Posted by stj View Post
no, it's supposed to be 0.27ohms

desolder coil L805, connect a 40w mains bulb to the pins of C812 and try it again.
then your only running the psu and the audio amp - not the rest of the circuit.
you need the light because the psu expects a load.
I will give this a go as i went and got some old 40w bulbs.
On my last 3.3uf resistor here so dont reallywant to blow it up too. Ive had some mox type 3.3uf resistors turn up but can i use them?.

Last edited by roadrash; 06-08-2019 at 04:58 AM..
roadrash is offline   Reply With Quote
Old 06-08-2019, 03:35 AM   #46
roadrash
Badcaps Veteran
 
roadrash's Avatar
 
Join Date: Oct 2015
City & State: Cambridgeshire
My Country: U.K.
Line Voltage: 240VAC
I'm a: Knowledge Seeker
Posts: 274
Default Re: Help with dead Commodore 1802

Quote:
Originally Posted by R_J View Post
So no short across the main capacitor?, You can also check the output transistor in the str54041 (E=pin4,C=pin3,B=pin2) however I suspect that if the str was bad it should have blown R805 (0.27Ω)
Just to make sure what is the number of the main capacitor?
roadrash is offline   Reply With Quote
Old 06-08-2019, 09:15 AM   #47
R_J
Badcaps Veteran
 
Join Date: Jun 2012
City & State: ☻
My Country: Canada
I'm a: Professional Tech
Posts: 4,133
Default Re: Help with dead Commodore 1802

It's the large one in the power supply C803
R_J is offline   Reply With Quote
Old 06-08-2019, 04:31 PM   #48
roadrash
Badcaps Veteran
 
roadrash's Avatar
 
Join Date: Oct 2015
City & State: Cambridgeshire
My Country: U.K.
Line Voltage: 240VAC
I'm a: Knowledge Seeker
Posts: 274
Default Re: Help with dead Commodore 1802

Can i use these metal oxide resistors if i blow my last wire wound one?
roadrash is offline   Reply With Quote
Old 06-08-2019, 07:55 PM   #49
R_J
Badcaps Veteran
 
Join Date: Jun 2012
City & State: ☻
My Country: Canada
I'm a: Professional Tech
Posts: 4,133
Default Re: Help with dead Commodore 1802

How many resistors do you have?, Use a metal oxide one and save the last wire wound. Use a incandescent lamp in series with the ac line untill you locate the problem.

Last edited by R_J; 06-08-2019 at 07:56 PM..
R_J is offline   Reply With Quote
Old 06-10-2019, 10:58 AM   #50
roadrash
Badcaps Veteran
 
roadrash's Avatar
 
Join Date: Oct 2015
City & State: Cambridgeshire
My Country: U.K.
Line Voltage: 240VAC
I'm a: Knowledge Seeker
Posts: 274
Default Re: Help with dead Commodore 1802

Quote:
Originally Posted by R_J View Post
So no short across the main capacitor?, You can also check the output transistor in the str54041 (E=pin4,C=pin3,B=pin2) however I suspect that if the str was bad it should have blown R805 (0.27Ω)
No short across main cap. Took out str54041 so how do i test this thing. My component tester only has 3 test leads. Can it be done with a multimeter? Here isna picture of what i removed there is not any room to get into it much.
Attached Images
File Type: jpg 20190610_175304.jpg (203.3 KB, 2 views)
roadrash is offline   Reply With Quote
Old 06-10-2019, 12:00 PM   #51
R_J
Badcaps Veteran
 
Join Date: Jun 2012
City & State: ☻
My Country: Canada
I'm a: Professional Tech
Posts: 4,133
Default Re: Help with dead Commodore 1802

You can test the output transistor with a meter, see post #44
Attached Files
File Type: pdf STR54041.pdf (160.9 KB, 0 views)

Last edited by R_J; 06-10-2019 at 12:01 PM..
R_J is offline   Reply With Quote
Old 06-10-2019, 01:16 PM   #52
roadrash
Badcaps Veteran
 
roadrash's Avatar
 
Join Date: Oct 2015
City & State: Cambridgeshire
My Country: U.K.
Line Voltage: 240VAC
I'm a: Knowledge Seeker
Posts: 274
Default Re: Help with dead Commodore 1802

Quote:
Originally Posted by R_J View Post
You can test the output transistor with a meter, see post #44
with a meter, see post #44[/QUOTE]

Thanks. It tests ok. Ive been testing everything including the STR54041 for a short and nothing tests as a short in the power supply area of the pcb except a odd iduction coils and that new metal oxcide resistor. Should i refit the STR transistor and try power it up using the light bulb as was mentioned earlier. Ive removed L805 and connected the bulb across C812. Is there anything to check before i try this and most likely blow another resistor probably.

Last edited by roadrash; 06-10-2019 at 01:17 PM..
roadrash is offline   Reply With Quote
Old 06-11-2019, 04:56 AM   #53
roadrash
Badcaps Veteran
 
roadrash's Avatar
 
Join Date: Oct 2015
City & State: Cambridgeshire
My Country: U.K.
Line Voltage: 240VAC
I'm a: Knowledge Seeker
Posts: 274
Default Re: Help with dead Commodore 1802

Ok i gave it one final check after solderig in the STR transistor we checked and as i was afraid of it blew the now mox resistor. Those resistors give a much bigger flash than the wire wound one's. Well that is still a bit strange because i checked all component for the psu and none were shorting. Am i right in assuming that that coil i removed is the output voltage from the psu to the monitor itself. So this rules out a monitor fault and the short is isolated to the psu circuit somewhere?
roadrash is offline   Reply With Quote
Old 06-11-2019, 12:23 PM   #54
stj
Great Sage 齊天大聖
 
stj's Avatar
 
Join Date: Dec 2009
City & State: Europe
My Country: some shithole run by Israeli agents
I'm a: Professional Tech
Posts: 20,761
Default Re: Help with dead Commodore 1802

yes, the coil is the link from the psu stage to the tube handling.
it does not isolate the audio amplifier though.
stj is offline   Reply With Quote
Old 06-11-2019, 12:37 PM   #55
roadrash
Badcaps Veteran
 
roadrash's Avatar
 
Join Date: Oct 2015
City & State: Cambridgeshire
My Country: U.K.
Line Voltage: 240VAC
I'm a: Knowledge Seeker
Posts: 274
Default Re: Help with dead Commodore 1802

I am not sure where to look now after not finding any shorted components in psu area of the pcb. Can you point where else I should check?
roadrash is offline   Reply With Quote
Old 06-11-2019, 02:30 PM   #56
stj
Great Sage 齊天大聖
 
stj's Avatar
 
Join Date: Dec 2009
City & State: Europe
My Country: some shithole run by Israeli agents
I'm a: Professional Tech
Posts: 20,761
Default Re: Help with dead Commodore 1802

so no shorted diodes or ceramic caps?
stj is offline   Reply With Quote
Old 06-11-2019, 03:33 PM   #57
roadrash
Badcaps Veteran
 
roadrash's Avatar
 
Join Date: Oct 2015
City & State: Cambridgeshire
My Country: U.K.
Line Voltage: 240VAC
I'm a: Knowledge Seeker
Posts: 274
Default Re: Help with dead Commodore 1802

I only checked inside the marked area of the psu and didnt check the ceramic caps. I checked all diodes and electrolytic caps. I didn't know that ceramic caps went short circuit. It is ok when the coils (Lxxx) show as a short I think isn't it?
roadrash is offline   Reply With Quote
Old 06-11-2019, 03:55 PM   #58
stj
Great Sage 齊天大聖
 
stj's Avatar
 
Join Date: Dec 2009
City & State: Europe
My Country: some shithole run by Israeli agents
I'm a: Professional Tech
Posts: 20,761
Default Re: Help with dead Commodore 1802

coils should look short - they are just a bit of wire,
ceramic caps are a bastard, they can go short without external signs, and withstand a LOT of current.
i have seen shorted ceramics blow tracks off the board!
stj is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



Badcaps.net Technical Forums 2003 - 2019
Powered by vBulletin ®
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
All times are GMT -6. The time now is 01:35 AM.
Did you find this forum helpful?