Badcaps.net Forum
Go Back   Badcaps Forums > Search Forums
Register FAQ Calendar Search Today's Posts Mark Forums Read

Showing results 1 to 11 of 11
Search took 0.00 seconds.
Search: Posts Made By: keeney123
Forum: General Electronics Technical Discussion 11-29-2015, 12:12 AM
Replies: 146
Views: 11,877
Posted By keeney123
Re: Need help reading a schematic.

I did not know that. Anyway, you found a way that works for you and there is nothing wrong with that.
Forum: General Electronics Technical Discussion 11-28-2015, 06:02 PM
Replies: 146
Views: 11,877
Posted By keeney123
Re: Need help reading a schematic.

So with the needle and the flux it is easy to use. Just small amount on the pad and solder. With the right tip on the iron one just puts some solder in the tip and just pull it down on the edge of...
Forum: General Electronics Technical Discussion 11-27-2015, 01:01 PM
Replies: 146
Views: 11,877
Posted By keeney123
Re: Need help reading a schematic.

The flux is to transfer the heat from the iron to the solder joint. It allow a even flow through the joint and helps to get rid of oxygen in the joint. If you have no flux in your solder, flux will...
Forum: General Electronics Technical Discussion 11-26-2015, 07:26 PM
Replies: 146
Views: 11,877
Posted By keeney123
Re: Need help reading a schematic.

Here is another company that carry the fiberglass TV alignment tools.
http://www.minute-man.com/acatalog/TV_and_Radio_Alignment_Tools.html

One more company look under soldering tools...
Forum: General Electronics Technical Discussion 11-26-2015, 06:41 PM
Replies: 146
Views: 11,877
Posted By keeney123
Re: Need help reading a schematic.

No it would be for tuning coils etc. in radios, like this

http://www.rf-microwave.com/en/shop/0/163-tuning-screwdrivers-for-capacitors-coils/1901-CT-4192.html

It can be anything that is small...
Forum: General Electronics Technical Discussion 11-25-2015, 11:30 PM
Replies: 146
Views: 11,877
Posted By keeney123
Re: Need help reading a schematic.

You can use like a Blunted fiberglass screwdriver to hold down the resister. First tin your iron then hold the resistor down with the instrument and tack one side of the resistor. After that is done...
Forum: General Electronics Technical Discussion 11-25-2015, 02:25 PM
Replies: 146
Views: 11,877
Posted By keeney123
Re: Need help reading a schematic.

One teacher I had told me they under rate resistor power by 40% for safety factor. This was on the carbon resistors.
Forum: General Electronics Technical Discussion 11-17-2015, 09:45 PM
Replies: 146
Views: 11,877
Posted By keeney123
Re: Need help reading a schematic.

Thanks for that info. I came across this Processor in a plug-in board that an Apple computer used in 1986. I believe at the time the board and the software was consider the driver.
Forum: General Electronics Technical Discussion 11-16-2015, 09:53 PM
Replies: 146
Views: 11,877
Posted By keeney123
Re: Need help reading a schematic.

is that a Rockwell processor?
Forum: General Electronics Technical Discussion 11-16-2015, 06:49 PM
Replies: 146
Views: 11,877
Posted By keeney123
Re: Need help reading a schematic.

Yes, it is a good way to proto-type a board as it is easy to unscrew the wire wraps to change the circuit connection. Only problem is that it is only good for about 2 years as the connection start to...
Forum: General Electronics Technical Discussion 11-16-2015, 12:20 AM
Replies: 146
Views: 11,877
Posted By keeney123
Re: Need help reading a schematic.

You'll get just hang in there. You have some good teachers. Are you using wire wraps or soldering?
Showing results 1 to 11 of 11

 
Forum Jump


Badcaps.net Technical Forums 2003 - 2021
Powered by vBulletin ®
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
All times are GMT -6. The time now is 08:41 AM.
Did you find this forum helpful?