Badcaps.net Forum
Go Back   Badcaps Forums > Search Forums
Register FAQ Calendar Search Today's Posts Mark Forums Read

Showing results 1 to 8 of 8
Search took 0.01 seconds.
Search: Posts Made By: PCBONEZ
Forum: Major Manufacturers Boards 12-10-2011, 07:35 PM
Replies: 30
Views: 8,658
Posted By PCBONEZ
Re: Dimension 8400 (yes I searched)

If it is in Vcore then yes.
Vcore voltage is less than 2.5v.
.
If not in Vcore then you need to check the circuit voltage and make sure it is 2.5v or less.
.
Forum: Major Manufacturers Boards 12-10-2011, 06:30 PM
Replies: 30
Views: 8,658
Posted By PCBONEZ
Re: Dimension 8400 (yes I searched)

KZG are a defective series. High failure rates.
It's all over the forum.
.
Forum: Major Manufacturers Boards 08-31-2011, 02:46 PM
Replies: 30
Views: 8,658
Posted By PCBONEZ
Re: Dimension 8400 (yes I searched)

Give that and what is here these would be what I'd use.
.
http://www.badcaps.net/store/product_info.php?cPath=3&products_id=153...
Forum: Major Manufacturers Boards 08-31-2011, 11:26 AM
Replies: 30
Views: 8,658
Posted By PCBONEZ
Re: Dimension 8400 (yes I searched)

The VR 100uF is 5mm and BNC only has 6mm
The VR 470uF is 6.3mm and BCN only has 8mm
-
Will larger diameter caps fit?
-
If not you need to look at digikey.com or mouser.com - if you are in the...
Forum: Major Manufacturers Boards 08-31-2011, 11:13 AM
Replies: 30
Views: 8,658
Posted By PCBONEZ
Re: Dimension 8400 (yes I searched)

Nichicon VZ is a direct replacement for VR but they are rated for 105C to VR's 85C.
Chemicon LXZ and Panasonic FC are better rated and usually easy to find.
There are actually a lot of options in...
Forum: Major Manufacturers Boards 08-31-2011, 10:47 AM
Replies: 30
Views: 8,658
Posted By PCBONEZ
Re: Dimension 8400 (yes I searched)

I think you need to read the 100uF again.
HN series doesn't go up to 25v and would be over-kill for that application.
The small uF caps are for EMI vice Ripple from the PSU.
That said a ZLG will...
Forum: Major Manufacturers Boards 07-25-2011, 08:32 AM
Replies: 30
Views: 8,658
Posted By PCBONEZ
Re: Dimension 8400 (yes I searched)

Yes. Agree.

Those 85C caps.
Intel -sometimes- uses 85C for the small caps since at least socket 370 [PIII].
I know they did it on some socket 775 boards too, and I think they still do it.
It's...
Forum: Major Manufacturers Boards 03-26-2010, 11:54 PM
Replies: 30
Views: 8,658
Posted By PCBONEZ
Re: Dimension 8400 (yes I searched)

You are getting good advice and correct info here.
If you aren't willing to replace them then it's time to scrap the board and build a new system.
.
Showing results 1 to 8 of 8

 
Forum Jump


Badcaps.net Technical Forums 2003 - 2019
Powered by vBulletin ®
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
All times are GMT -6. The time now is 05:00 PM.
Did you find this forum helpful?