Hello
I'm looking for a circuit diagram for Philips 42pfl6877k12
That's how it is for me
When I turn on the TV, the standby light comes on for 1 second then nothing happens again
Thank you
Thank you to the guys at HEGE supporting Badcaps [ HEGE ] [ HEGE DEX Chart ]
Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
Hi Budm, could you take a look at my post
[url]https://www.badcaps.net/forum/showthread.php?t=114778[/url]https://Hi Budm, could you take a lo...t=114778[/url]
-
Re: RXD26L Kenwood hi-fi schematic / advice please
What DC V do you get with ref to the circuit ground on the middle pin of the white power resistors of both channel AFTER the protection kicks in?
-
Re: Ryobi 18v BCL14181H MY2015 charger dead
Is the fuse (red body) F2 (right next to ZD4) OK?
It is an always on power supply that is why you are getting 30V on the cold side.Last edited by budm; 02-17-2022, 11:20 PM.
Leave a comment:
-
Re: Using a Variac to simulate UPS battery
This was what I did in t he lab to test the UPS without having the batteries around, it is just enough to make the UPS run at low AC load.
I use old UPS transformer 120VAC side fed by the VARIAC, the low Voltage side (low Voltage high current winding which was used to be driven by the MOSFET's and get the DC from the batteries) is connected to high current bridge rectifier and lot of high capacitor bank.
for example if the 12V output is drawing 10A, the AC side fed by VARIAC will only draw a little over 1ACA. With is setup you...
Leave a comment:
-
Re: Transistor or V regulator identification - help
The schematic drawing does not match the board layout, for example: the resistor 8061 is directly connected between Base and the Collector pin of the Transistor, but the drawing shows it has Thermistor connected to the Base first then to the 8061 resistor.
Did you use diode mode to test the junctions of this Transistor?
Leave a comment:
-
Re: LED Resistor Calculations ...
Is it really 117c not 117f?
If it is that hot I wonder what the junction Temp of the LED is.
Typical 1W white LED has junction temp max of around 110c.
[url]https://www.photonics.com/Articles/Measuring_LED_Junction_Temperature/a34316[/url]Re: LED Resistor Calculations ...<br...ing_LED_JunctiLast edited by budm; 05-25-2021, 09:18 PM.
Leave a comment:
-
Re: Help diagnose no power on Changhong board
So c910 running cap in the hot side checked out OK for sure?
Leave a comment:
-
-
Re: LG 55UJ6200 BEFORE & AFTER tape fix/fine tuning success
Bad caps can be replaced if you have experience with SMD repair and have proper tools.
Example of bad MLCC:
[url]https://www.badcaps.net/forum/showthread.php?p=1043044#post1043044[/url]Re: LG 55UJ6200 BEFORE & AFTER tape ...t1043044[/url]Last edited by budm; 05-07-2021, 03:30 PM.
Leave a comment:
-
Re: Sonos Playbase S11 dead. No led at the front
So you also have 3.3V, so far you do have 5V and 3.3V to run the logic circuits.
What is the history of the unit? It mat be FW issue. Did you do any search to see if other people have the same similar issue?...
Leave a comment:
-
Re: Samsung ue32h5500 backlight but no picture
Are the tab bonding boards on the bottom edge of the LCD panel?
Inspect the tab bonding boards for any sign of damage and also check the resistance on the MLCC's (Multi Layer Ceramic Cap) of the tab bonding boards to see if any of them show low resistance reading....
Leave a comment:
-
Re: Sharp LC-40LE810UN Zero Power
Pin 1 and 2 are in the hot side, so the circuit ground will be the negative leg of the main filter cap in the hot side. What ground did you use?
And the reason I have you measure right between the two leg so the meter is not reference to the circuit gnd, we are measuring the Vf of the LED inside the Opto.
BTW, when the meter shows -1 that tend to indicate over range....
Leave a comment:
-
Re: 42pfl5432d/37 no picture but have sound
Not going to work as design at heavy load, the inverters can easily draw 5A or more. I would replace all 3 of them that is what I would do first. When cap is domed up like that the ESR will be high and the capacitance can also drop down in value too, you can also have bad cap with no sign of bulging at all but it can have high ESR.
If you look at the traces from each white fuse back to the 24V power connector, you will see it all connected through a bunch of '0' jumper (black device with '0' printed on top),...
Leave a comment:
-
Re: 42pfl5432d/37 no picture but have sound
The tops of those two green caps do not look flat to me.
Leave a comment:
-
Re: 42pfl5432d/37 no picture but have sound
I just look at your power supply board, I see two caps for the 24V power supply have domed tops, Can you inspect and verify them and provide clearer pictures?...Last edited by budm; 05-01-2021, 11:07 PM.
Leave a comment:
No activity results to display
Show More
Leave a comment: